MC74HC4316ADR2
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| Series | 74HC |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 130Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MC74HC4316A |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Temperature Grade | MILITARY |
| Number of Channels | 1 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 40μA |
| Number of Bits | 4 |
| Throw Configuration | SPST |
| Propagation Delay | 40 ns |
| Turn On Delay Time | 130 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Supply Type | Dual |
| Bandwidth | 150MHz |
| Neg Supply Voltage-Nom (Vsup) | -4.5V |
| Turn-Off Delay Time | 130 ns |
| Max Dual Supply Voltage | 6V |
| Min Dual Supply Voltage | 1V |
| Off-state Isolation-Nom | 40 dB |
| On-state Resistance Match-Nom | 25Ohm |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 60ns |
| Switch-off Time-Max | 60ns |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC74HC4316ADR2 Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. High reliability is ensured by the advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. Totally, there are 16 terminations. A 1 channel electronic part produces high-quality output. Powered by a 4.5V voltage supply, the electrical part should be switched on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. Try searching for MC74HC4316A variants of the analog switch ic. It has an internal resistance of 130Ohm. You can find the functions of the 16 pins in the datasheets. This switch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 6V. Analogue multiplexer with a Dual supply type that is cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. For this multiplexer to operate, 40μA current would be sufficient. For this multiplexer, dual supply voltage is feasible, but it should not exceed 6V. It is recommended that you attach at least 1V to your dual power supply. There are SEPARATE OUTPUT outputs on this analog switch ic. 150MHz-bandwidths can be used to transfer data between multiplexers. A temperature above 125°C is not suitable for operation of the analogue multiplexer. It can conduct in a 4-bit manner. This is electronic component of the 74HC series.
MC74HC4316ADR2 Features
1 Channels
40μA Supply Current
Bandwidth: 150MHz
4-Bit
MC74HC4316ADR2 Applications
There are a lot of ON Semiconductor MC74HC4316ADR2 Analog Switches & Multiplexers ICs applications.
- Medical Instrumentation
- E1 Network Equipment
- Low-Voltage
- Precision test equipment
- Relay Replacement
- Digital cross connects (DSX-1)
- Public switching systems
- Microprocessor controlled systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- ISDN NT1/TA
