MC74HC574ADWG
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2005 |
| Series | 74HC |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Tin (Sn) |
| Subcategory | FF/Latches |
| Packing Method | RAIL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74HC574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 7.8mA |
| Number of Bits | 8 |
| Clock Frequency | 35MHz |
| Propagation Delay | 240 ns |
| Turn On Delay Time | 27 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 27ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.4mm |
| Length | 12.95mm |
| Width | 7.6mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MC74HC574ADWG Overview
The flip flop is packaged in a case of 20-SOIC (0.295, 7.50mm Width). There is an embedded version in the package Tube. This output is configured with Tri-State, Non-Inverted. Positive Edgeis the trigger it is configured with. Surface Mountis in the way of this electric part. The JK flip flop operates at 2V~6Vvolts. A temperature of -55°C~125°C TAis used in the operation. This logic flip flop is classified as type D-Type. It is a type of FPGA belonging to the 74HC series. It should not exceed 35MHzin terms of its output frequency. A total of 1 elements are present. There is 4μA quiescent consumption. 20terminations have occurred. It is a member of the 74HC574 family. The D flip flop is powered by a voltage of 3V . This T flip flop has a capacitance of 10pF farads at the input. HC/UHis the family of this D flip flop. In this case, the electronic component is mounted in the way of Surface Mount. As you can see from the design, it has pins with 20. The clock edge trigger type for this device is Positive Edge. This device is part of the FF/Latchesbase part number family. The flip flop is designed with 8bits. The maximal supply voltage (Vsup) reaches 6V. Normal operation requires a supply voltage (Vsup) above 2V. In view of its reliability, this D flip flop is a good fit for RAIL. The system runs on a power supply of 2/6V watts. This D flip flop is equipped with 0 ports. With an output current of 7.8mA, this device offers maximum design flexibility. There are 3 output lines in this JK flip flop. It is reported that there are 8 channels.
MC74HC574ADWG Features
Tube package
74HC series
20 pins
8 Bits
2/6V power supplies
MC74HC574ADWG Applications
There are a lot of ON Semiconductor MC74HC574ADWG Flip Flops applications.
- Set-reset capability
- Latch-up performance
- High Performance Logic for test systems
- Dynamic threshold performance
- Functionally equivalent to the MC10/100EL29
- 2 – Bit synchronous counter
- Buffered Clock
- Parallel data storage
- ATE
- Convert a momentary switch to a toggle switch
