MC74HC574ADWR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 22 hours ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| Series | 74HC |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74HC574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 7.8mA |
| Number of Bits | 8 |
| Clock Frequency | 35MHz |
| Propagation Delay | 240 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 27 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Halogen Free | Halogen Free |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 27ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MC74HC574ADWR2G Overview
As a result, it is packaged as 20-SOIC (0.295, 7.50mm Width). D flip flop is included in the Tape & Reel (TR)package. As configured, the output uses Tri-State, Non-Inverted. The trigger it is configured with uses Positive Edge. Surface Mountis occupied by this electronic component. The JK flip flop operates with an input voltage of 2V~6V volts. It is operating at -55°C~125°C TA. It is an electronic flip flop with the type D-Type. The FPGA belongs to the 74HC series. This D flip flop should not have a frequency greater than 35MHz. D latch consists of 1 elements. 20terminations have occurred. The 74HC574 family contains it. A voltage of 3V provides power to the D latch. Its input capacitance is 10pF farads. The electronic device belongs to the HC/UHfamily. There is an electronic part mounted in the way of Surface Mount. The 20pins are designed into the board. There is a clock edge trigger type of Positive Edgeon this device. This RS flip flops is a part number FF/Latches. There are 8bits in its design. There is a 6Vmaximum supply voltage (Vsup). Normal operation requires a supply voltage (Vsup) above 2V. On the basis of its reliable performance, this D flip flop is well suited for use with TAPE AND REEL. The D latch runs on a voltage of 2/6V volts. The flip flop has 2embedded ports. As a result of its output current of 7.8mA, it is very flexible in terms of design. To operate, the chip has a total of 3 output lines. This D latch consumes 4μA quiescent current at all. It is reported that there are 8 channels.
MC74HC574ADWR2G Features
Tape & Reel (TR) package
74HC series
20 pins
8 Bits
2/6V power supplies
MC74HC574ADWR2G Applications
There are a lot of ON Semiconductor MC74HC574ADWR2G Flip Flops applications.
- Circuit Design
- Data Synchronizers
- Cold spare funcion
- Storage Registers
- Differential Individual
- Safety Clamp
- Control circuits
- Buffer registers
- Computing
- Dynamic threshold performance
