MC74HC574ANG
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Weight | 4.535924g |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2009 |
| Series | 74HC |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Tin (Sn) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74HC574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 7.8mA |
| Number of Bits | 8 |
| Clock Frequency | 35MHz |
| Propagation Delay | 240 ns |
| Turn On Delay Time | 27 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 27ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 3.56mm |
| Length | 27.17mm |
| Width | 6.6mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
MC74HC574ANG Overview
The item is packaged in 20-DIP (0.300, 7.62mm)cases. As part of the package Tube, it is embedded. Currently, the output is configured to use Tri-State, Non-Inverted. The trigger it is configured with uses Positive Edge. The electronic part is mounted in the way of Through Hole. A voltage of 2V~6Vis used as the supply voltage. The operating temperature is -55°C~125°C TA. This logic flip flop is classified as type D-Type. JK flip flop is a part of the 74HCseries of FPGAs. Its output frequency should not exceed 35MHz. D latch consists of 1 elements. It consumes 4μA of quiescent Currently, there are 20 terminations. The 74HC574 family contains it. The D flip flop is powered by a voltage of 3V . Input capacitance of this device is 10pF farads. It belongs to the family of electronic devices known as HC/UH. A part of the electronic system is mounted in the way of Through Hole. It is designed with 20 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This RS flip flops is a part number FF/Latches. The flip flop is designed with 8bits. It reaches the maximum supply voltage (Vsup) at 6V. For normal operation, the supply voltage (Vsup) should be above 2V. Despite its superior flexibility, it relies on 8 circuits to achieve it. A power supply of 2/6Vis required to operate it. A D flip flop with 2embedded ports is available. In addition to its maximum design flexibility, the output current of the T flip flop is 7.8mA. There are 3 output Lines, which generate the binary equivalent of the input line whose value is equal to “1” and are available to encode either a decimal or hexadecimal input pattern to typically a binary or “B. C. D” (binary coded decimal) output code.
MC74HC574ANG Features
Tube package
74HC series
20 pins
8 Bits
2/6V power supplies
MC74HC574ANG Applications
There are a lot of ON Semiconductor MC74HC574ANG Flip Flops applications.
- Latch
- Bus hold
- ESCC
- Parallel data storage
- EMI reduction circuitry
- Safety Clamp
- ATE
- Data storage
- Patented noise
- Divide a clock signal by 2 or 4
