MC74HCT374ADWR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2002 |
| Series | 74HCT |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74HCT374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Channels | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 35mA |
| Number of Bits | 8 |
| Clock Frequency | 30MHz |
| Propagation Delay | 47 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 31 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Halogen Free | Halogen Free |
| Current - Output High, Low | 6mA 6mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 31ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.4mm |
| Length | 12.95mm |
| Width | 7.6mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MC74HCT374ADWR2G Overview
It is packaged in the way of 20-SOIC (0.295, 7.50mm Width). A package named Tape & Reel (TR)includes it. This output is configured with Tri-State, Non-Inverted. JK flip flop uses Positive Edgeas the trigger. There is an electronic component mounted in the way of Surface Mount. A 4.5V~5.5Vsupply voltage is required for it to operate. It is at -55°C~125°C TAdegrees Celsius that the system is operating. D-Typedescribes this flip flop. The 74HCTseries comprises this type of FPGA. There should be no greater frequency than 30MHzon its output. The list contains 1 elements. Terminations are 20. The 74HCT374family includes it. A voltage of 5V is used as the power supply for this D latch. This JK flip flop has a 10pFfarad input capacitance. In this case, the D flip flop belongs to the HCTfamily. There is an electronic part that is mounted in the way of Surface Mount. A total of 20pins are provided on this board. A Positive Edgeclock edge trigger is used in this device. There is a FF/Latchesbase part number assigned to the RS flip flops. Flip flops designed with 8bits are used in this part. In view of its reliability, this D flip flop is a good fit for TAPE AND REEL. An electrical current of 5V volts is applied to it. A D flip flop with 2embedded ports is available. For high efficiency, the supply voltage should be set to 5V. The 35mA output current allows it to be designed with the greatest amount of flexibility. It is designed with 3 output lines. In terms of quiescent current, it consumes 4μA . A total of 8 channels are available.
MC74HCT374ADWR2G Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
5V power supplies
MC74HCT374ADWR2G Applications
There are a lot of ON Semiconductor MC74HCT374ADWR2G Flip Flops applications.
- Single Up Count-Control Line
- Test & Measurement
- 2 – Bit synchronous counter
- Data Synchronizers
- Buffered Clock
- Dynamic threshold performance
- Latch
- Functionally equivalent to the MC10/100EL29
- Storage registers
- Computers
