MC74HCT4851ADR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 400Ohm |
| Terminal Finish | Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MC74HCT4851A |
| Pin Count | 16 |
| Power Supplies | 5V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 2μA |
| Power Dissipation | 500mW |
| Logic Function | Demultiplexer, Multiplexer |
| Halogen Free | Halogen Free |
| Supply Type | Single |
| Supply Current-Max (Isup) | 0.04mA |
| On-State Resistance (Max) | 400Ohm |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Number of Input Lines | 11 |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 40pF |
| On-state Resistance Match-Nom | 80Ohm |
| Switch-on Time-Max | 40ns |
| Switch-off Time-Max | 40ns |
| Voltage - Supply, Single (V+) | 4.5V~5.5V |
| Signal Current-Max | 0.025A |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MC74HCT4851ADR2G Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. 8:1 is the ratio of multiplexer to demultiplexer circuits. Around -55°C~125°C TA is the extended operating temperature. In total, there are 16 terminations. By its 8 channels, the electronic component provides high-quality output. With a 5V voltage supply, the electrical component should be turned on and run. Electronic part bodies are injected with 16 pins. Circuits number 1 make up this analogue multiplexer. Try searching for MC74HCT4851A variants of the analog switch ic. As far as internal resistance is concerned, it has 400Ohm. Please refer to the datasheets for 16 pins functions. There is Multiplexer or Switches analog multiplexer like this in the world. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. Analogue multiplexer with a Single supply type that is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 4.5V. For this digital switch to work, 2μA current would suffice. A voltage of 4.5V~5.5V is required to drain this analog switch from a single voltage supply.
MC74HCT4851ADR2G Features
8 Channels
2μA Supply Current
MC74HCT4851ADR2G Applications
There are a lot of ON Semiconductor MC74HCT4851ADR2G Analog Switches & Multiplexers ICs applications.
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Multiplexers
- Switching Systems
- Frame Relay Equipment
- RGB switches
- Digital access cross connects
- Central office
- Channelized and Unchannelized DS3 applications
- Audio signal routing
- PDAs
