MC74HCT574ADTR2
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74HCT574 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 30MHz |
| Propagation Delay | 30 ns |
| Turn On Delay Time | 30 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 6mA 6mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 30ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC74HCT574ADTR2 Overview
The flip flop is packaged in a case of 20-TSSOP (0.173, 4.40mm Width). The Tape & Reel (TR)package contains it. T flip flop uses Tri-State, Non-Invertedas the output. It is configured with a trigger that uses Positive Edge. There is an electric part mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. It is operating at a temperature of -55°C~125°C TA. It belongs to the type D-Typeof flip flops. In this case, it is a type of FPGA belonging to the 74HCT series. This D flip flop should not have a frequency greater than 30MHz. A total of 1 elements are present. As a result, it consumes 4μA quiescent current and is not affected by external forces. There are 20 terminations,The 74HCT574 family contains it. A voltage of 5V is used as the power supply for this D latch. There is 10pF input capacitance for this T flip flop. In this case, the D flip flop belongs to the HCTfamily. A part of the electronic system is mounted in the way of Surface Mount. There are 20pins on it. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The part is included in FF/Latches. There are 8bits in its design. The superior flexibility is achieved through the use of 8 circuits. Considering its reliability, this T flip flop is well suited for TAPE AND REEL. A total of 5V power supplies are needed to run it. The flip flop contains 2ports. For high efficiency, the supply voltage should be set to 5V. There are 3 output Lines, which generate the binary equivalent of the input line whose value is equal to “1” and are available to encode either a decimal or hexadecimal input pattern to typically a binary or “B. C. D” (binary coded decimal) output code.
MC74HCT574ADTR2 Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
5V power supplies
MC74HCT574ADTR2 Applications
There are a lot of ON Semiconductor MC74HCT574ADTR2 Flip Flops applications.
- Data storage
- Automotive
- Communications
- Individual Asynchronous Resets
- Reduced system switching noise
- Count Modes
- Instrumentation
- ESD performance
- Latch-up performance
- Registers
