MC74HCT574ADW
| Parameters | |
|---|---|
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 30MHz |
| Propagation Delay | 30 ns |
| Turn On Delay Time | 30 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 6mA 6mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 30ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2009 |
| Series | 74HCT |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Tin (Sn) |
| Subcategory | FF/Latches |
| Packing Method | RAIL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 225 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HCT574 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
MC74HCT574ADW Overview
It is embeded in 20-SOIC (0.295, 7.50mm Width) case. Package Tubeembeds it. Currently, the output is configured to use Tri-State, Non-Inverted. It is configured with the trigger Positive Edge. There is an electronic component mounted in the way of Surface Mount. A 4.5V~5.5Vsupply voltage is required for it to operate. In the operating environment, the temperature is -55°C~125°C TA. It belongs to the type D-Typeof flip flops. This type of FPGA is a part of the 74HCT series. In order for it to function properly, its output frequency should not exceed 30MHz. A total of 1elements are contained within it. As a result, it consumes 4μA of quiescent current without being affected by external factors. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. It is a member of the 74HCT574 family. The power supply voltage is 5V. The input capacitance of this JK flip flopis 10pF farads. An electronic device belonging to the family HCTcan be found here. There is an electronic part that is mounted in the way of Surface Mount. There are 20pins on it. A Positive Edgeclock edge trigger is used in this device. This device is part of the FF/Latchesbase part number family. The design is based on 8bits. In this case, the maximum supply voltage (Vsup) reaches 5.5V. Normally, the supply voltage (Vsup) should be kept above 4.5V. The superior flexibility of this circuit is achieved by using 8 circuits. In light of its reliable performance, this T flip flop is well suited for RAIL. In order for the device to operate, it requires 5V power supplies. The D flip flop has no ports embedded. It has 3 output lines to operate.
MC74HCT574ADW Features
Tube package
74HCT series
20 pins
8 Bits
5V power supplies
MC74HCT574ADW Applications
There are a lot of ON Semiconductor MC74HCT574ADW Flip Flops applications.
- Digital electronics systems
- Clock pulse
- Load Control
- Data transfer
- ESCC
- Power down protection
- ATE
- Buffered Clock
- High Performance Logic for test systems
- 2 – Bit synchronous counter
