MC74HCT574ANG
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2005 |
| Series | 74HCT |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Tin (Sn) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74HCT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 6mA |
| Number of Bits | 8 |
| Clock Frequency | 30MHz |
| Propagation Delay | 30 ns |
| Turn On Delay Time | 30 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 6mA 6mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 30ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 4.57mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
MC74HCT574ANG Overview
20-DIP (0.300, 7.62mm)is the packaging method. It is contained within the Tubepackage. This output is configured with Tri-State, Non-Inverted. It is configured with the trigger Positive Edge. There is an electric part mounted in the way of Through Hole. With a supply voltage of 4.5V~5.5V volts, it operates. It is operating at a temperature of -55°C~125°C TA. The type of this D latch is D-Type. In FPGA terms, D flip flop is a type of 74HCTseries FPGA. You should not exceed 30MHzin the output frequency of the device. D latch consists of 1 elements. T flip flop consumes 4μA quiescent energy. Currently, there are 20 terminations. If you search by 74HCT574, you will find similar parts. Power is provided by a 5V supply. A JK flip flop with a 10pFfarad input capacitance is used here. Devices in the HCTfamily are electronic devices. Through Hole mounts this electronic component. 20pins are included in its design. This device exhibits a clock edge trigger type of Positive Edge. This device is part of the FF/Latchesbase part number family. An electronic part designed with 8bits is used in this application. Its superior flexibility is attributed to its use of 8 circuits. A total of 5V power supplies are needed to run it. The flip flop has 2embedded ports. In order to achieve high efficiency, the supply voltage should be maintained at 5V. In addition to its maximum design flexibility, the output current of the T flip flop is 6mA. It has 3 output lines to operate.
MC74HCT574ANG Features
Tube package
74HCT series
20 pins
8 Bits
5V power supplies
MC74HCT574ANG Applications
There are a lot of ON Semiconductor MC74HCT574ANG Flip Flops applications.
- ESCC
- Asynchronous counter
- Reduced system switching noise
- Patented noise
- Parallel data storage
- Guaranteed simultaneous switching noise level
- Load Control
- Dynamic threshold performance
- Consumer
- Instrumentation
