MC74LCX574DTR2
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| Series | 74LCX |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74LCX574 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 3.3V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 150MHz |
| Propagation Delay | 9.5 ns |
| Turn On Delay Time | 1.5 ns |
| Family | LVC/LCX/Z |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 10μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 8.5ns @ 3.3V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 7pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC74LCX574DTR2 Overview
In the form of 20-TSSOP (0.173, 4.40mm Width), it has been packaged. There is an embedded version in the package Tape & Reel (TR). There is a Tri-State, Non-Invertedoutput configured with it. The trigger it is configured with uses Positive Edge. Surface Mountis occupied by this electronic component. The JK flip flop operates with an input voltage of 2V~3.6V volts. Temperature is set to -40°C~85°C TA. It belongs to the type D-Typeof flip flops. The 74LCXseries comprises this type of FPGA. In order for it to function properly, its output frequency should not exceed 150MHz. In total, it contains 1 elements. This process consumes 10μA quiescents. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The object belongs to the 74LCX574 family. An input voltage of 3.3Vpowers the D latch. Its input capacitance is 7pFfarads. This D flip flop belongs to the family of LVC/LCX/Z. There is an electronic part that is mounted in the way of Surface Mount. Basically, it is designed with a set of 20 pins. Its clock edge trigger type is Positive Edge. The part is included in FF/Latches. It is designed with a number of bits of 8. Normally, the supply voltage (Vsup) should be kept above 2V. Its flexibility is enhanced by 8 circuits. This D flip flop is well suited for TAPE AND REEL based on its reliable performance. There are 2 ports embedded in the flip flops. Optimal efficiency requires a supply voltage of 3.3V. To operate, the chip has a total of 3 output lines.
MC74LCX574DTR2 Features
Tape & Reel (TR) package
74LCX series
20 pins
8 Bits
MC74LCX574DTR2 Applications
There are a lot of ON Semiconductor MC74LCX574DTR2 Flip Flops applications.
- ESCC
- Registers
- Event Detectors
- Matched Rise and Fall
- Frequency Dividers
- Single Down Count-Control Line
- Parallel data storage
- Reduced system switching noise
- Count Modes
- Instrumentation
