MC74LVX4051D
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 55Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MC74LVX4051 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2.5V |
| Operating Supply Current | 40μA |
| Power Dissipation | 500mW |
| Propagation Delay | 40 ns |
| Turn On Delay Time | 40 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 2.5V~6V ±2.5V~6V |
| Supply Type | Single |
| Bandwidth | 80MHz |
| Neg Supply Voltage-Nom (Vsup) | -3V |
| Turn-Off Delay Time | 40 ns |
| Max Dual Supply Voltage | 3V |
| On-State Resistance (Max) | 26Ohm |
| Min Dual Supply Voltage | 1.25V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF |
| On-state Resistance Match-Nom | 15Ohm |
| Charge Injection | 12pC |
| Channel-to-Channel Matching (ΔRon) | 10 Ω |
| Signal Current-Max | 0.02A |
| Length | 9.9mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC74LVX4051D Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). Advanced packaging method Tube is used to provide high reliability. The multiplexer is located in Surface Mount. There is 8:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of -55°C~125°C TA degrees Celsius. In total, there are 16 terminations. A high-quality output is provided by the electrical component's 8 channels. When the electronic component is given a voltage of 3V, it should be turned on and run. This electronic part can be found in the 16 series. The multiplexer consists of 1 circuits. Try searching for the analog switch ic with MC74LVX4051 if you are looking for variants. In this multiplexer, the internal resistance is 55Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. In this analog multiplexer, the value is Multiplexer or Switches. In normalcircumstances, users should not exceed 6V volts for the multiplexer. A analog switch ic that has a cost-effective Single supply type. The lowest voltage fed to the electronic component should be 2.5V. The switch device would be able to operate with 40μA current. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 3V. A dual power supply should have at least 1.25V voltage attached. Operating the 8 inputs requires 8 inputs. 80MHz-bandwidths can be used to transfer data between multiplexers.
MC74LVX4051D Features
8 Channels
40μA Supply Current
Bandwidth: 80MHz
MC74LVX4051D Applications
There are a lot of ON Semiconductor MC74LVX4051D Analog Switches & Multiplexers ICs applications.
- Digital cross connects (DSX-1)
- Multi-Line E1 Interface Cards
- PDH Multiplexers
- PBX interfaces
- Intelligent PBX
- RGB switches
- Communications systems
- Fiber In The Loop (FITL)
- Frame Relay Equipment
- Avionics and Military Systems
