MC74VHC1G66DFT2
| Parameters | |
|---|---|
| Turn-Off Delay Time | 40 ns |
| -3db Bandwidth | 180MHz |
| On-State Resistance (Max) | 40Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF |
| Switch Circuit | SPST - NO |
| Switching | MAKE-BEFORE-BREAK |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NO |
| Length | 2mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Lifecycle Status | OBSOLETE (Last Updated: 13 hours ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2004 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 40Ohm |
| Terminal Finish | Tin/Lead (Sn80Pb20) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 150mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MC74VHC1G66 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 25mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 40 ns |
| Supply Type | Single |
MC74VHC1G66DFT2 Overview
Shipping overseas is convenient due to the electrical component's packing in 5-TSSOP, SC-70-5, SOT-353. High reliability is achieved by using advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature around -55°C~125°C TA extended. The total number of terminations is 5. A high-quality output is provided by the electrical component's 1 channels. An 3V voltage supply should allow the electrical part to be turned on and run. A total of 5 pins are injected into the electrical part body. On the other hand, analog switches can be constructed using SPST - NO switching circuits. There are 1 circuits in this switch device. Use MC74VHC1G66 to search for variants of the digital switches. There is 40Ohm internal resistance in this digital multiplexer. Please refer to the datasheets for 5 pins functions. In this analog multiplexer, the value is Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. The analog switch ic is of the Single supply type and is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 2V. The analogue multiplexer could operate on 1μA current. Using only a single voltage supply, this analog switch requires 2V~5.5V voltage. A voltage higher than 25mA may cause damage to the switch multiplexer. 5V operating voltages can be used with this electrical part.
MC74VHC1G66DFT2 Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 180MHz
MC74VHC1G66DFT2 Applications
There are a lot of ON Semiconductor MC74VHC1G66DFT2 Analog Switches & Multiplexers ICs applications.
- PBX interfaces
- Microwave transmission systems
- Microprocessor controlled systems
- Audio signal routing
- Switching Systems
- Imaging
- ISDN NT1/TA
- HDTV
- Low-Voltage
- Data Acquisition Systems
