Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 21 hours ago) |
Contact Plating |
Tin |
Mounting Type |
Surface Mount |
Package / Case |
SOT-23-5 Thin, TSOT-23-5 |
Surface Mount |
YES |
Number of Pins |
5 |
Operating Temperature |
-55°C~125°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2007 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
5 |
Resistance |
100Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
200mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
3V |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
MC74VHC1G66 |
Pin Count |
5 |
Operating Supply Voltage |
5V |
Polarity |
Non-Inverting |
Power Supplies |
5V |
Number of Channels |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
2V |
Operating Supply Current |
1μA |
Nominal Supply Current |
25mA |
Power Dissipation |
200mW |
Max Supply Current |
25mA |
Throw Configuration |
SPST |
Turn On Delay Time |
40 ns |
Number of Inputs |
1 |
Halogen Free |
Halogen Free |
Supply Type |
Single |
Bandwidth |
180MHz |
Turn-Off Delay Time |
40 ns |
On-State Resistance (Max) |
40Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
80 dB |
Current - Leakage (IS(off)) (Max) |
100nA |
Channel Capacitance (CS(off), CD(off)) |
10pF |
Switch Circuit |
SPST - NO |
Switching |
MAKE-BEFORE-BREAK |
Voltage - Supply, Single (V+) |
2V~5.5V |
Normal Position |
NO |
Height |
1mm |
Length |
3mm |
Width |
1.5mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MC74VHC1G66DTT1G Overview
The electrical component comes in SOT-23-5 Thin, TSOT-23-5 packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. The operating temperature is extended to around -55°C~125°C TA. The total number of terminations is 5. As a result of its 1 channels, this electronic component provides high-quality output. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. A key feature of the 5 series is the inclusion of this electronic part as part of its design. Multiplexers built on a SPST - NO switching circuit are built. Search with MC74VHC1G66 if you are looking for analog multiplexer variants. The internal resistance of this digital multiplexer is 100Ohm. To find out what the functions of 5 pins are, please refer to their datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. normally, users should not supply switches with voltages higher than 5.5V. Analogue multiplexer with a Single supply type that is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 2V. 1μA current would be enough for this multiplexer to operate. This analogue multiplexer requires a voltage of 2V~5.5V when it drains from a single voltage supply. Put voltage above 25mA on the multiplexer to cause damage. Operating voltages of 5V are compatible with the electrical part. There are 1 inputs to be operated. It is possible to transfer data over a 180MHz-bandwidth.
MC74VHC1G66DTT1G Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
Bandwidth: 180MHz
MC74VHC1G66DTT1G Applications
There are a lot of ON Semiconductor MC74VHC1G66DTT1G Analog Switches & Multiplexers ICs applications.
- Digital Cross-Connects
- Private Branch Exchange (PBX)
- High reliability control systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Mechanical reed relay replacement
- Communication systems
- Fiber to the Home
- Medical Instrumentation
- Microwave transmission systems
- Voice over IP/DSL – Integrated Access Devices, Smart