MC74VHC574DT
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2011 |
| Series | 74VHC |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | RAIL |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74VHC574 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 2/5.5V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 115MHz |
| Propagation Delay | 16.7 ns |
| Turn On Delay Time | 5.6 ns |
| Family | AHC/VHC |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 10.6ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC74VHC574DT Overview
The package is in the form of 20-TSSOP (0.173, 4.40mm Width). A package named Tubeincludes it. T flip flop uses Tri-State, Non-Invertedas its output configuration. JK flip flop uses Positive Edgeas the trigger. It is mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 2V~5.5V. A temperature of -40°C~85°C TAis used in the operation. There is D-Type type of electronic flip flop associated with this device. This type of FPGA is a part of the 74VHC series. A frequency of 115MHzshould not be exceeded by its output. A total of 1elements are present in it. T flip flop consumes 4μA quiescent energy. A total of 20terminations have been recorded. You can search similar parts based on 74VHC574. Power is supplied from a voltage of 3.3V volts. The input capacitance of this T flip flop is 4pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. This D flip flop belongs to the family of AHC/VHC. A part of the electronic system is mounted in the way of Surface Mount. The 20pins are designed into the board. It has a clock edge trigger type of Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. The flip flop is designed with 8bits. Vsup reaches 5.5V, the maximal supply voltage. The supply voltage (Vsup) should be maintained above 2V for normal operation. Using 8 circuits, it is highly flexible. Due to its reliability, this T flip flop is well suited for RAIL. A power supply of 2/5.5Vis required to operate it. The flip flop has 2ports embedded within it. It operates with 3 output lines.
MC74VHC574DT Features
Tube package
74VHC series
20 pins
8 Bits
2/5.5V power supplies
MC74VHC574DT Applications
There are a lot of ON Semiconductor MC74VHC574DT Flip Flops applications.
- Parallel data storage
- 2 – Bit synchronous counter
- Count Modes
- Functionally equivalent to the MC10/100EL29
- Synchronous counter
- Cold spare funcion
- Memory
- Clock pulse
- ESD protection
- Bus hold
