MC74VHCT574ADT
| Parameters | |
|---|---|
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | RAIL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74VHCT574 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 130MHz |
| Propagation Delay | 10.4 ns |
| Turn On Delay Time | 4.1 ns |
| Family | AHCT/VHCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 10.4ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 95000000Hz |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2011 |
| Series | 74VHCT |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
MC74VHCT574ADT Overview
In the form of 20-TSSOP (0.173, 4.40mm Width), it has been packaged. It is contained within the Tubepackage. There is a Tri-State, Non-Invertedoutput configured with it. It is configured with a trigger that uses Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. A temperature of -40°C~85°C TAis considered to be the operating temperature. There is D-Type type of electronic flip flop associated with this device. In FPGA terms, D flip flop is a type of 74VHCTseries FPGA. In order for it to function properly, its output frequency should not exceed 130MHz. The list contains 1 elements. As a result, it consumes 4μA quiescent current and is not affected by external forces. There have been 20 terminations. If you search by 74VHCT574, you will find similar parts. The power source is powered by 5V. The input capacitance of this JK flip flopis 4pF farads. Devices in the AHCT/VHCTfamily are electronic devices. A part of the electronic system is mounted in the way of Surface Mount. The 20pins are designed into the board. This device's clock edge trigger type is Positive Edge. The part you are looking for is included in FF/Latches. There are 8bits in this flip flop. The superior flexibility of this circuit is achieved by using 8 circuits. In view of its reliability, this D flip flop is a good fit for RAIL. A total of 5V power supplies are needed to run it. The D flip flop has no ports embedded. For high efficiency, the supply voltage should be set to 5V. In order for the chip to function, it has 3output lines.
MC74VHCT574ADT Features
Tube package
74VHCT series
20 pins
8 Bits
5V power supplies
MC74VHCT574ADT Applications
There are a lot of ON Semiconductor MC74VHCT574ADT Flip Flops applications.
- Computing
- Balanced Propagation Delays
- Single Up Count-Control Line
- Digital electronics systems
- QML qualified product
- Frequency Dividers
- ESCC
- Guaranteed simultaneous switching noise level
- Computers
- Matched Rise and Fall
