MC74VHCT574ADTRG
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 15 hours ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| Series | 74VHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74VHCT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Channels | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 130MHz |
| Propagation Delay | 10.4 ns |
| Turn On Delay Time | 4.1 ns |
| Family | AHCT/VHCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Halogen Free | Halogen Free |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 10.4ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 95000000Hz |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MC74VHCT574ADTRG Overview
The item is packaged in 20-TSSOP (0.173, 4.40mm Width)cases. You can find it in the Tape & Reel (TR)package. As configured, the output uses Tri-State, Non-Inverted. This trigger is configured to use Positive Edge. There is an electronic component mounted in the way of Surface Mount. The supply voltage is set to 4.5V~5.5V. Temperature is set to -40°C~85°C TA. It is an electronic flip flop with the type D-Type. This type of FPGA is a part of the 74VHCT series. In order for it to function properly, its output frequency should not exceed 130MHz. D latch consists of 1 elements. It consumes 4μA of quiescent current without being affected by external factors. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. If you search by 74VHCT574, you will find similar parts. The power source is powered by 5V. The input capacitance of this T flip flop is 4pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. A device of this type belongs to the family of AHCT/VHCT. There is an electronic component mounted in the way of Surface Mount. The 20pins are designed into the board. This device has the clock edge trigger type of Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. An electronic part designed with 8bits is used in this application. Considering its reliability, this T flip flop is well suited for TAPE AND REEL. A power supply of 5Vis required to operate it. This flip flop has a total of 2ports. High efficiency requires the supply voltage to be maintained at 5V. In order to operate, the chip has 3 output lines. The number of channels is growing strong/weak: 8.
MC74VHCT574ADTRG Features
Tape & Reel (TR) package
74VHCT series
20 pins
8 Bits
5V power supplies
MC74VHCT574ADTRG Applications
There are a lot of ON Semiconductor MC74VHCT574ADTRG Flip Flops applications.
- Functionally equivalent to the MC10/100EL29
- Registers
- Bus hold
- Safety Clamp
- Automotive
- Modulo – n – counter
- Matched Rise and Fall
- Count Modes
- Data storage
- Clock pulse
