MC74VHCT74ADTR2G
| Parameters | |
|---|---|
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 8.8ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Number of Output Lines | 1 |
| fmax-Min | 80 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 65000000Hz |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| Series | 74VHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74VHCT74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Clock Frequency | 140MHz |
| Propagation Delay | 13 ns |
| Turn On Delay Time | 6.3 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 2μA |
| Halogen Free | Halogen Free |
| Current - Output High, Low | 8mA 8mA |
| Max I(ol) | 0.008 A |
MC74VHCT74ADTR2G Overview
It is embeded in 14-TSSOP (0.173, 4.40mm Width) case. The Tape & Reel (TR)package contains it. T flip flop uses Differentialas the output. This trigger uses the value Positive Edge. There is an electric part mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. Currently, the operating temperature is -55°C~125°C TA. This D latch has the type D-Type. It belongs to the 74VHCTseries of FPGAs. It should not exceed 140MHzin its output frequency. There is 2μA quiescent consumption. A total of 14 terminations have been made. The 74VHCT74 family contains it. It is powered by a voltage of 5V . JK flip flop input capacitance is 4pF farads. The electronic device belongs to the AHCT/VHCT/VTfamily. In this case, the electronic component is mounted in the way of Surface Mount. There are 14pins on it. Its clock edge trigger type is Positive Edge. This RS flip flops is a part number FF/Latches. Its superior flexibility is attributed to its use of 2 circuits. In view of its reliability, this D flip flop is a good fit for TAPE AND REEL. A total of 5V power supplies are needed to run it. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. There are 1 output lines in this JK flip flop.
MC74VHCT74ADTR2G Features
Tape & Reel (TR) package
74VHCT series
14 pins
5V power supplies
MC74VHCT74ADTR2G Applications
There are a lot of ON Semiconductor MC74VHCT74ADTR2G Flip Flops applications.
- Differential Individual
- Dynamic threshold performance
- High Performance Logic for test systems
- Reduced system switching noise
- Convert a momentary switch to a toggle switch
- Circuit Design
- Common Clocks
- Memory
- Data transfer
- Synchronous counter
