MCP100-460DI/TO
| Parameters | |
|---|---|
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | TO-226-3, TO-92-3 (TO-226AA) |
| Number of Pins | 3 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Bulk |
| Published | 1998 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Number of Functions | 1 |
| Supply Voltage | 4.35V |
| Base Part Number | MCP100 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 3 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 60μA |
| Nominal Supply Current | 60μA |
| Max Supply Current | 60μA |
| Adjustable Threshold | NO |
| Quiescent Current | 45μA |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 4.475V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 150ms Minimum |
| Min Reset Threshold Voltage | 4.35V |
| Max Reset Threshold Voltage | 4.6V |
| Threshold Voltage | +4.48V |
| Undervoltage Threshold | 4.35V |
| Overvoltage Threshold | 4.6V |
| Height | 4.62mm |
| Length | 4.71mm |
| Width | 3.62mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
MCP100-460DI/TO Overview
It is mounted through 3 terminals on the power management. There is a Bulk-packaging method applied to IC management. There are 1 functions included in this PMIC so that you can refer to them. On this supervisor, there is a series of 1 channels that can be found. As a reference, this IC power includes TO-226-3, TO-92-3 (TO-226AA) functions for your convenience. There are many benefits that this IC power shares with other Simple Reset/Power-On Reset products as well. IC management conducts at a voltage of 4.35V. In a 1 supply voltage, the PMIC chip conducts. Through Hole is the one that mounts power management. It is possible to subcategorize this power ic as a Power Management Circuits chip. Power management has a total of 3 pins. The pins of the power management system count 3. It is recommended that the minimum supply voltage (Vsup) for this IC management should not be less than 1V volts. Voltage (Vsup) shouldn't exceed 5.5V volts in this PMIC. The recommended mounting type for IC management is Through Hole. This power management is the recommended temperature range for the supervisors: -40°C~85°C TA. When this power management system is in operation, it produces an output voltage of Push-Pull, Totem Pole. In order to maintain a stable supply current for the power management, 60μA is the recommended value. You can always use MCP100, the base supervisor number, to search for similar PMICs of the manufacturer. At the most, voltage supervisor can work with a supply temperature of 60μA.
MCP100-460DI/TO Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
60μA operating supply current
MCP100-460DI/TO Applications
There are a lot of Microchip Technology MCP100-460DI/TO Voltage Supervisors applications.
- Power distribution systems of infant care room
- Electric heating appliances
- Medical-specific insulation monitor
- Detection of phase sequence
- Dash board
- DSP
- Battery cars
- Radar
- Important electronics for automotive protection
- Telecommunications equipment
