MCP100-485DI/TO
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | TO-226-3, TO-92-3 (TO-226AA) |
| Number of Pins | 3 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Bulk |
| Published | 2018 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Power Management Circuits |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Number of Functions | 1 |
| Supply Voltage | 4.6V |
| Base Part Number | MCP100 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 3 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 60μA |
| Nominal Supply Current | 45μA |
| Max Supply Current | 60μA |
| Adjustable Threshold | NO |
| Quiescent Current | 45μA |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 4.725V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 150ms Minimum |
| Min Reset Threshold Voltage | 4.6V |
| Max Reset Threshold Voltage | 4.85V |
| Threshold Voltage | +4.73V |
| Undervoltage Threshold | 4.6V |
| Overvoltage Threshold | 4.85V |
| Height | 4.62mm |
| Length | 4.71mm |
| Width | 3.62mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP100-485DI/TO Overview
As you can see, this power management is mounted through 3 terminals. There is a Bulk-packaging method applied to IC management. The purpose of this IC management is to provide you with a reference of 1 functions. This power managment ic consists of 1 channels, each of which can be used independently. In this IC management you will find TO-226-3, TO-92-3 (TO-226AA) functions for you to refer to. This IC power shares lots of benefits with other Simple Reset/Power-On Reset products. When a supply voltage of 4.6V is applied to the power ic, it conducts. Power management conducts at a voltage of 1. The power management is mounted by a Through Hole-axis. The power management belongs to the Power Management Circuits subcategory. In total, the power management has 3 pins in it. This power management has 3 pins. It is recommended that Vsup should not be less than 1V for this IC power. Voltage (Vsup) shouldn't exceed 5.5V volts in this PMIC. Power management recommends the Through Hole mounting type. The temperature of the supervisors should be set to this range: -40°C~85°C TA. Power management has an output of Push-Pull, Totem Pole during operation. As far as the supply current of the power management is concerned, it is 60μA. To find similar IC managements from the manufacturer, you can always search by MCP100. A maximum supply temperature of 60μA can be used with this power management.
MCP100-485DI/TO Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
60μA operating supply current
MCP100-485DI/TO Applications
There are a lot of Microchip Technology MCP100-485DI/TO Voltage Supervisors applications.
- DSP
- Satellite navigation
- Efficient information transmission
- Radio
- Urban rail transit weak current power monitoring
- Digitally controlled LDO regulators circuit
- Detection of phase sequence
- Battery-powered equipment
- FPGA design
- Stable power system
