MCP100T-450I/TT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-236-3, SC-59, SOT-23-3 |
| Number of Pins | 3 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1998 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 4.25V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP100 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 3 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 60μA |
| Nominal Supply Current | 60μA |
| Max Supply Current | 60μA |
| Adjustable Threshold | NO |
| Quiescent Current | 45μA |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 4.375V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 150ms Minimum |
| Min Reset Threshold Voltage | 4.25V |
| Max Reset Threshold Voltage | 4.5V |
| Threshold Voltage | +4.38V |
| Undervoltage Threshold | 4.25V |
| Overvoltage Threshold | 4.5V |
| Height | 950μm |
| Length | 2.9mm |
| Width | 1.3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP100T-450I/TT Overview
This voltage supervisor has a total of 3 mounting terminals that can be used for mounting. Packaged in a Tape & Reel (TR)-shape, IC management comes with a number of features. The purpose of this IC management is to provide you with a reference of 1 functions. This power managment ic consists of 1 channels, each of which can be used independently. The purpose of this IC power is to provide you with a reference of TO-236-3, SC-59, SOT-23-3 functions. There are a number of benefits that this PMIC has in common with other Simple Reset/Power-On Reset manage ics. IC management is specified that the package peak reflow temperature should be 260. When a supply voltage of 4.25V is applied to the power ic, it conducts. In a 1 supply voltage, the PMIC chip conducts. The mount is provided by Surface Mount. In this case, this PMIC chip can be sub-categorized as a Power Management Circuits chip. In total, IC powers are 3 pins on the board. Pin count of the power management is 3. Supply voltage (Vsup) should be at least 1V for this power management. The maximum supply voltage (Vsup) in this PMIC should not exceed 5.5V volts. The recommended mounting type for IC management is Surface Mount. The temperature of the supervisors should be set to this range: -40°C~85°C TA. As a result of this supervisor's operation, the output voltage is Push-Pull, Totem Pole. For this power management, there is an 60μA volt supply current. To find similar IC managements from the manufacturer, you can always search by MCP100. A maximum supply temperature of 60μA can be used.
MCP100T-450I/TT Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
60μA operating supply current
MCP100T-450I/TT Applications
There are a lot of Microchip Technology MCP100T-450I/TT Voltage Supervisors applications.
- Multi-voltage system
- Stable power system
- Microcontroller system
- Electronics installed in the vehicle
- Telecommunications equipment
- Power distribution systems of infant care room
- Important electronics for automotive protection
- Battery-powered equipment
- Digitally controlled LDO regulators circuit
- Detection of phase sequence
