MCP102T-475E/TT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-236-3, SC-59, SOT-23-3 |
| Number of Pins | 3 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Terminal Pitch | 0.96mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP102 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 3 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 1.75μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1.75μA |
| Adjustable Threshold | NO |
| Quiescent Current | 1μA |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 4.63V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 80ms Minimum |
| Min Reset Threshold Voltage | 4.561V |
| Max Reset Threshold Voltage | 4.7V |
| Threshold Voltage | +4.63V |
| Undervoltage Threshold | 4.561V |
| Overvoltage Threshold | 4.7V |
| Height | 1.02mm |
| Length | 3.04mm |
| Width | 1.4mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP102T-475E/TT Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 3 in total. A Tape & Reel (TR) package is used to package the power management. In this PMIC, you can find 1 functions for your reference. There are 1 channels on this power managment ic that can be found in a series. To assist you, this PMIC includes TO-236-3, SC-59, SOT-23-3 functions. There are a number of benefits that this PMIC has in common with other Simple Reset/Power-On Reset manage ics. Specifies a reflow peak temperature of 260 for the package during reflow. A supply voltage of 1 is used to conduct the PMIC chip. Power management is included in the Surface Mount mount. This power ic can be sub-categorized as Power Management Circuits. The total number of pins on this power management is 3. 3 pins make up the power management. A voltage (Vsup) that doesn't fall below 1V as the minimum supply voltage (Vsup) should be applied to this IC power in order to ensure its proper operation. This IC power should be powered by no more than 5.5V volts of supply voltage (Vsup). Power management' mounting is recommended to be done with the Surface Mount type of mounting. The supervisors should be set to the following temperature: -40°C~125°C TA. There is an output voltage of Push-Pull, Totem Pole from this supervisor when it is operating. As far as the supply current of the power management is concerned, it is 1.75μA. To find similar IC managements from the manufacturer, you can always search by MCP102. At most, voltage supervisor can operate at a supply temperature of 1.75μA.
MCP102T-475E/TT Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
1.75μA operating supply current
MCP102T-475E/TT Applications
There are a lot of Microchip Technology MCP102T-475E/TT Voltage Supervisors applications.
- Radar
- Unattended substation automation
- Rechargeable batteries
- Dash board
- Battery cars
- Electronics installed in the vehicle
- WiFi router
- DSP
- DVR
- Network equipment
