MCP103T-270E/LB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-70, SOT-323 |
| Number of Pins | 3 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP103 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 3 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 1.75μA |
| Max Supply Current | 1.75μA |
| Adjustable Threshold | NO |
| Quiescent Current | 1μA |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 2.63V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 80ms Minimum |
| Min Reset Threshold Voltage | 2.591V |
| Max Reset Threshold Voltage | 2.67V |
| Threshold Voltage | +2.63V |
| Undervoltage Threshold | 2.591V |
| Overvoltage Threshold | 2.67V |
| Length | 2.025mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP103T-270E/LB Overview
This voltage supervisor has a total of 3 mounting terminals that can be used for mounting. A Tape & Reel (TR) package is used to package the power management. In this PMIC, you can find 1 functions for your reference. There are 1 channels on this power managment ic that can be found in a series. In this IC management you will find SC-70, SOT-323 functions for you to refer to. There are a number of benefits that this PMIC has in common with other Simple Reset/Power-On Reset manage ics. Specifies a reflow peak temperature of 260 for the package during reflow. A supply voltage of 1 is used to conduct the PMIC chip. The power management is mounted by Surface Mount. The power management system can be categorized as a Power Management Circuits chip. In total, the power management has 3 pins in it. 3 pins are present on the power management system. It is recommended that Vsup should not be less than 1V for this IC power. During this IC power, the maximum supply voltage (Vsup) should not exceed 5.5V volts. The recommended mounting type is Surface Mount. We recommend setting the supervisors to -40°C~125°C TA degrees. The output voltage of this power managment ic during operation is Push-Pull, Totem Pole. It is estimated that the voltage supervisor's supply current is 1.75μA. It is always advisable to use MCP103, the base supervisor number, when searching for similar PMICs from the manufacturer. The maximum supply temperature that PMIC chip can work with is 1.75μA.
MCP103T-270E/LB Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
1.75μA operating supply current
MCP103T-270E/LB Applications
There are a lot of Microchip Technology MCP103T-270E/LB Voltage Supervisors applications.
- Digitally controlled LDO regulators circuit
- Battery cars
- FPGA design
- Set top box
- Functional modules
- Insulation fault location system
- Power communication system
- Important electronics for automotive protection
- Efficient information transmission
- Unattended substation automation
