banner_page

MCP120-475I/SN

5V8 Terminals 8-Pin MCP120 Voltage supervisor1 Channels Min 1V Max 5.5V


  • Manufacturer: Microchip Technology
  • Nocochips NO: 536-MCP120-475I/SN
  • Package: 8-SOIC (0.154, 3.90mm Width)
  • Datasheet: PDF
  • Stock: 668
  • Description: 5V8 Terminals 8-Pin MCP120 Voltage supervisor1 Channels Min 1V Max 5.5V (Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 8-SOIC (0.154, 3.90mm Width)
Number of Pins 8
Operating Temperature -40°C~85°C TA
Packaging Tube
Published 1998
JESD-609 Code e3
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
ECCN Code EAR99
Type Simple Reset/Power-On Reset
Terminal Finish Matte Tin (Sn)
Subcategory Power Management Circuits
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 5V
Time@Peak Reflow Temperature-Max (s) 40
Base Part Number MCP120
Output Open Drain or Open Collector
Pin Count 8
Number of Channels 1
Max Supply Voltage 5.5V
Min Supply Voltage 1V
Operating Supply Current 60μA
Nominal Supply Current 60μA
Max Supply Current 60μA
Adjustable Threshold NO
Quiescent Current 45μA
Watchdog Timer No
Reset Active Low
Voltage - Threshold 4.625V
Number of Voltages Monitored 1
Reset Timeout 150ms Minimum
Min Reset Threshold Voltage 4.5V
Max Reset Threshold Voltage 4.75V
Threshold Voltage +4.63V
Undervoltage Threshold 4.5V
Overvoltage Threshold 4.75V
Length 4.9mm
Width 3.9mm
RoHS Status ROHS3 Compliant
Lead Free Lead Free

MCP120-475I/SN Overview


Power management is mounted through 8 terminals. There is a Tube-packaging method applied to IC management. There are 1 functions included in this PMIC so that you can refer to them. This power management is made up of 1 channels which are available in a series format. In this IC management you will find 8-SOIC (0.154, 3.90mm Width) functions for you to refer to. With power management, you get a lot of benefits that you won't find in other Simple Reset/Power-On Reset products. IC management is specified that the package peak reflow temperature should be 260. Manage ics operate at 5V supply voltages. When a supply voltage of 1 is applied to the power ic, it conducts. The power management is mounted by Surface Mount. Power Management Circuits is a subcategory of this PMIC chip. A total of 8 pins are located on this power management. 8 pins are on the supervisor. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 1V. Voltage (Vsup) shouldn't exceed 5.5V volts in this PMIC. Power management recommends the Surface Mount mounting type. The temperature of the supervisors should be set to this range: -40°C~85°C TA. There is an output voltage of Open Drain or Open Collector from this supervisor when it is operating. It is estimated that the voltage supervisor's supply current is 60μA. For similar manage ics search of the manufacturer, you can always refer to MCP120, the base PMIC number. Voltage supervisor can work with a supply temperature of 60μA at the most.

MCP120-475I/SN Features


Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
60μA operating supply current

MCP120-475I/SN Applications


There are a lot of Microchip Technology MCP120-475I/SN Voltage Supervisors applications.

  • DSP
  • Solar power charger
  • Insulation fault location system
  • Automotive permanent magnet synchronous motors
  • Electronics installed in the vehicle
  • Digitally controlled LDO regulators circuit
  • FPGA design
  • Precision measurement
  • Urban rail transit weak current power monitoring
  • Telecommunications equipment

Write a review

Note: HTML is not translated!
    Bad           Good