MCP120T-315I/SN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1998 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP120 |
| Output | Open Drain or Open Collector |
| Pin Count | 8 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 60μA |
| Nominal Supply Current | 60μA |
| Max Supply Current | 60μA |
| Adjustable Threshold | NO |
| Quiescent Current | 45μA |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 3.075V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 150ms Minimum |
| Min Reset Threshold Voltage | 3V |
| Max Reset Threshold Voltage | 3.15V |
| Threshold Voltage | +3.08V |
| Undervoltage Threshold | 3V |
| Overvoltage Threshold | 3.15V |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP120T-315I/SN Overview
There are 8 terminals on this power management that allow it to be mounted. A Tape & Reel (TR) package is used to package the power management. Power management is possible to find a series of 1 functions. On this supervisor, there is a series of 1 channels that can be found. IC management is packaged as a 8-SOIC (0.154, 3.90mm Width) package. There are a lot of similarities between this IC power and other Simple Reset/Power-On Reset products. Packages are specified to have an average peak reflow temperature of 260. In a 5V supply voltage, the power management conducts. When a supply voltage of 1 is applied to the power ic, it conducts. By Surface Mount, IC management has been mounted. A IC power such as this can be classified as a Power Management Circuits power management system. There are a total of 8 pins on power management. There are 8 pins on the supervisor. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 1V. In this PMIC, the maximum supply voltage (Vsup) should not exceed 5.5V volts. In this case, Surface Mount is the recommended mounting type. It is recommended that the supervisor be set to this temperature: -40°C~85°C TA. When this power management system is in operation, it produces an output voltage of Open Drain or Open Collector. The supply current of the power management is 60μA. You can always use MCP120, the base supervisor number, to search for similar PMICs of the manufacturer. The maximum supply temperature that PMIC chip can work with is 60μA.
MCP120T-315I/SN Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
60μA operating supply current
MCP120T-315I/SN Applications
There are a lot of Microchip Technology MCP120T-315I/SN Voltage Supervisors applications.
- Detection of phase sequence
- Urban rail transit weak current power monitoring
- Microprocessor system
- Satellite navigation
- Battery cars
- Fire equipment power monitoring system
- Radio
- Important electronics for automotive safety
- Insulation fault location system
- Medical-specific isolation transformer
