MCP121-240E/TO
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | TO-226-3, TO-92-3 (TO-226AA) |
| Number of Pins | 3 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Bulk |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Terminal Position | BOTTOM |
| Terminal Form | WIRE |
| Number of Functions | 1 |
| Base Part Number | MCP121 |
| Output | Open Drain or Open Collector |
| Pin Count | 3 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 20μA |
| Adjustable Threshold | NO |
| Quiescent Current | 1μA |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 2.32V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 80ms Minimum |
| Min Reset Threshold Voltage | 2.285V |
| Max Reset Threshold Voltage | 2.355V |
| Threshold Voltage | +2.32V |
| Undervoltage Threshold | 2.285V |
| Overvoltage Threshold | 2.355V |
| Height | 4.95mm |
| Length | 4.95mm |
| Width | 3.94mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP121-240E/TO Overview
This power management consists of 3 mounting terminals on which it can be mounted. Packaged in the form of a Bulk, power management is easy to use. Please refer to this PMIC for 1 functions. On this supervisor, there is a series of 1 channels that can be found. IC management is packaged as a TO-226-3, TO-92-3 (TO-226AA) package. As with other Simple Reset/Power-On Reset products, this IC management also offers a wide range of benefits. IC management conducts in a 1-voltage supply. The mount is attached to Through Hole. This power ic can be sub-categorized as Power Management Circuits. In total, the power management has 3 pins in it. This power management has 3 pins. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 1V. Voltage (Vsup) shouldn't exceed 5.5V volts in this PMIC. Mounting type Through Hole is recommended. Temperature setting for the supervisors should be -40°C~125°C TA. During operation, this power management system outputs Open Drain or Open Collector. As far as the supply current of the power management is concerned, it is 20μA. It is always advisable to use MCP121, the base supervisor number, when searching for similar PMICs from the manufacturer. The maximum supply temperature that PMIC chip can work with is 20μA.
MCP121-240E/TO Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
20μA operating supply current
MCP121-240E/TO Applications
There are a lot of Microchip Technology MCP121-240E/TO Voltage Supervisors applications.
- Medical-specific isolation transformer
- Rechargeable batteries
- Kitchen appliances
- Stable power system
- Telecommunications equipment
- Detection of phase loss
- Solar power charger
- Household appliances
- Microcontroller system
- Electric heating appliances
