MCP1318T-46LE/OT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 240mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP1318 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 5 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 10μA |
| Power Dissipation | 240mW |
| Max Supply Current | 10μA |
| Adjustable Threshold | NO |
| Quiescent Current | 1μA |
| Watchdog Timer | Yes |
| Reset | Active High/Active Low |
| Voltage - Threshold | 4.6V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.531V |
| Max Reset Threshold Voltage | 4.669V |
| Threshold Voltage | +4.6V |
| Undervoltage Threshold | 4.531V |
| Overvoltage Threshold | 4.669V |
| Height | 1.3mm |
| Length | 3.1mm |
| Width | 1.8mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
MCP1318T-46LE/OT Overview
There are 5 terminals on this power management that allow it to be mounted. Packaging is in the form of a Tape & Reel (TR). There are 1 functions included in this PMIC so that you can refer to them. Depending on the power managment ic you are looking at, you can find a total of 1 channels. In this PMIC, you can find SC-74A, SOT-753 functions for your reference. There are a number of benefits that this PMIC has in common with other Simple Reset/Power-On Reset manage ics. According to the specification, the package's peak reflow temperature is specified to be 260. A supply voltage of 1 is used to conduct the PMIC chip. Surface Mount is the one that mounts power management. A IC power such as this can be classified as a Power Management Circuits power management system. It has a total of 5 pins that are attached to IC management. There are 5 pins on the power managment ic. In order for this PMIC to work correctly, the minimum supply voltage (Vsup) should be greater than 1V. The maximum supply voltage (Vsup) in this PMIC should not exceed 5.5V volts. A Surface Mount mounting type is recommended. The supervisors should be set to the following temperature: -40°C~125°C TA. Power management has an output of Push-Pull, Totem Pole during operation. There is a supply current of 10μA for the power management. To find similar IC managements from the manufacturer, you can always search by MCP1318. Voltage supervisor can work with a supply temperature of 10μA at the most.
MCP1318T-46LE/OT Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
10μA operating supply current
MCP1318T-46LE/OT Applications
There are a lot of Microchip Technology MCP1318T-46LE/OT Voltage Supervisors applications.
- Detection of phase sequence
- Network equipment
- Electric heating appliances
- Military electronics
- Automotive permanent magnet synchronous motors
- Dash board
- WiFi router
- Data storage applications
- Power distribution systems of CCU
- Utility meter
