MCP1320T-29FE/OT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Digi-Reel® |
| Published | 1999 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Type | Simple Reset/Power-On Reset |
| Max Power Dissipation | 240mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MCP1320 |
| Output | Open Drain or Open Collector |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 10μA |
| Power Dissipation | 240mW |
| Max Supply Current | 10μA |
| Adjustable Threshold | NO |
| Quiescent Current | 1μA |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 2.9V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 20ms Minimum |
| Min Reset Threshold Voltage | 2.857V |
| Max Reset Threshold Voltage | 2.944V |
| Undervoltage Threshold | 2.857V |
| Overvoltage Threshold | 2.944V |
| Height | 1.3mm |
| Length | 3.1mm |
| Width | 1.8mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MCP1320T-29FE/OT Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 5 in total. A Digi-Reel? package is used to package the power management. The purpose of this IC management is to provide you with a reference of 1 functions. There are 1 channels on this power managment ic that can be found in a series. In this IC management you will find SC-74A, SOT-753 functions for you to refer to. Compared to other Simple Reset/Power-On Reset products, this PMIC has a lot of benefits to offer. When a supply voltage of 5V is applied to the power ic, it conducts. Power ics operate at 1 supply voltages. The mount is attached to Surface Mount. This power management has 5 pins. It is recommended that the minimum supply voltage (Vsup) for this IC management should not be less than 1V volts. This IC power should be powered by no more than 5.5V volts of supply voltage (Vsup). The mounting type of the supervisors is Surface MountIt is recommended to set the supervisor's temperature to this range: -40°C~125°C TA. As this power managment ic operates, it is able to produce an output voltage of Open Drain or Open Collector. The power management's supply current is 10μA. It is always advisable to use MCP1320, the base supervisor number, when searching for similar PMICs from the manufacturer. The maximum supply temperature is 10μA.
MCP1320T-29FE/OT Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
10μA operating supply current
MCP1320T-29FE/OT Applications
There are a lot of Microchip Technology MCP1320T-29FE/OT Voltage Supervisors applications.
- Power distribution systems of operating room
- Microprocessor system
- Telecommunications equipment
- FPGA design
- Detection of phase sequence
- Insulation fault location system
- Leakage protection
- Smartphones
- Power distribution systems of ICU
- Rechargeable batteries
