MCP14E8T-E/SN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | MOSFET Drivers |
| Max Power Dissipation | 699mW |
| Voltage - Supply | 4.5V~18V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP14E8 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Qualification Status | Not Qualified |
| Max Output Current | 2A |
| Power Supplies | 4.5/18V |
| Nominal Supply Current | 1.8mA |
| Output Current | 2A |
| Max Supply Current | 1.8mA |
| Input Type | Inverting, Non-Inverting |
| Rise Time | 12ns |
| Fall Time (Typ) | 15 ns |
| Rise / Fall Time (Typ) | 12ns 15ns |
| Interface IC Type | HALF BRIDGE BASED MOSFET DRIVER |
| Channel Type | Independent |
| Number of Drivers | 2 |
| Turn On Time | 0.035 μs |
| Output Peak Current Limit-Nom | 2A |
| Driven Configuration | Low-Side |
| Gate Type | IGBT, N-Channel, P-Channel MOSFET |
| Current - Peak Output (Source, Sink) | 2A 2A |
| High Side Driver | YES |
| Logic Voltage - VIL, VIH | 0.8V 2.4V |
| Turn Off Time | 0.04 μs |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP14E8T-E/SN Overview
Its 8-SOIC (0.154, 3.90mm Width) package provides greater flexibility.Tape & Reel (TR) is the form of the package.This device is equipped with 2 drivers for its configuration.Its recommended mounting way is Surface Mount.In the absence of a 4.5V~18V supply voltage, it can demonstrate its superiority.A gate type of IGBT, N-Channel, P-Channel MOSFET has been used in its design.For this device, the temperature range is -40°C~150°C TJ.Inverting, Non-Inverting is the input type used in this program.The configuration starts with 8 terminations.Many related parts can be found under its base part number MCP14E8.In order to operate, a voltage of 12V has to be applied.Mosfet driver is equipped wMosfet driverh an interface chip HALF BRIDGE BASED MOSFET DRIVER.There is a maximum output current of 2A that can be achieved.There are several useful electronic components in this subcategory of MOSFET Drivers.The board has 8 component pins.The device is capable of delivering a current of 2A.The maximum power dissipation of 699mW shows its maximum capability to transfer and conduct power loss without overheating.To maintain higher stability, the supply current should always be 1.8mA.Based on its power supplies of 4.5/18V, it solves the problem of power supply failure for a variety of applications.
MCP14E8T-E/SN Features
Embedded in the Tape & Reel (TR) package
2 drivers
Employing a gate type of IGBT, N-Channel, P-Channel MOSFET
Maximum power dissipation of 699mW
MCP14E8T-E/SN Applications
There are a lot of Microchip Technology MCP14E8T-E/SN gate drivers applications.
- Multicolor LED/laser displays
- Welding
- Commercial and agricultural vehicles (CAV)
- 48 V to 12 V PoL Converters, 48 V to Low Voltage Bus Converter,
- Power factor correction (PFC) circuits
- Portable computers
- Industrial Power Supplies
- Motor Control
- Refrigerator
- Solar power supplies
