MCP1631-E/SS
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP1631 |
| Function | Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 5V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 5V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 250mA |
| Voltage - Supply (Vcc/Vdd) | 3V~5.5V |
| Control Features | Enable, Frequency Control, Ramp |
| Input Voltage (Min) | 3V |
| Topology | Sepic |
| Control Mode | CURRENT-MODE |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 2.5ns |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 2.7 ns |
| Switcher Configuration | SINGLE |
| Max Frequency | 2MHz |
| Switching Frequency | 2MHz |
| Duty Cycle | 10 % |
| Height | 1.75mm |
| Length | 7.2mm |
| Width | 5.3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP1631-E/SS Overview
With a 20-SSOP (0.209, 5.30mm Width) package, the switching controller is suitable for a wide range of applications. 1 outputs can be generated with the dc motor controller. PMIC packaging is solid with a Tube enclosure. Transistor Driver dc switching's outputs (s) can be handled by it. A 3V~5.5V voltage is supplied to the dc control and used for operating it. Worked in an dc switcher with a -40°C~125°C TJ rating. The Surface Mount value makes it suitable for general dc dc regulator. Switching control is made easier with the dcdc regulator's Enable, Frequency Control, Ramp. SWITCHING CONTROLLER analog IC connects the switch converters. A switching converters's terminal (s) sits at the DUAL position. An array of 20 terminations of dc switching. A few of the control techniques these dc dc converter ics adapt include PULSE WIDTH MODULATION. 5V nominal DC switcher's voltage input. Other relevant dc to dc converter ics can be found by searching "MCP1631". 20 pins are present on switching converter. Switching converter type is specifically Switching Regulator or Controllers. The minimum input voltage of the dc dc voltage regulator should be 3V. The test statistics indicate that DC regulator outputs a voltage of 5V. In most cases, the output current of the dc dc regulator will be 250mA, so note that when you start the project. Because of DC switcher's Surface Mount, it is suitable for most prototype designs and applications. DC regulator's maximum frequency is 2MHz. 2MHz is the frequency at which this controller can mostly perform fine.
MCP1631-E/SS Features
Transistor Driver Outputs
Enable, Frequency Control, Ramp
PULSE WIDTH MODULATION
Switching Frequency: 2MHz
MCP1631-E/SS Applications
There are a lot of Microchip Technology MCP1631-E/SS DC to DC converter applications.
- Telecommunications equipment
- Surge protection circuits
- Sink circuits
- Adjustable voltage or current linear circuits
- Electrical power transmission
- Electric heating, lighting
- Computer monitoring equipment of building
- Computer application technology
- Imported equipment
- Fire elevators
