MCP1631V-E/ST
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.65mm |
| Frequency | 1MHz |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP1631 |
| Function | Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 5V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 250mA |
| Voltage - Supply (Vcc/Vdd) | 3V~5.5V |
| Control Features | Enable, Frequency Control, Ramp |
| Topology | Sepic |
| Control Mode | VOLTAGE-MODE |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 2.5ns |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 2.7 ns |
| Nominal Input Voltage | 5.5V |
| Switcher Configuration | SINGLE |
| Max Duty Cycle | 10 % |
| Switching Frequency | 2MHz |
| Duty Cycle | 0 % |
| Height | 1.05mm |
| Length | 6.6mm |
| Width | 4.5mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
MCP1631V-E/ST Overview
With its 20-TSSOP (0.173, 4.40mm Width) package, the switching controller fits the needs of most applications. dc motor controller is suitable for 1 output generation. An enclosure of Tube is used to package the PMIC. Transistor Driver dc switching's outputs (s) can be handled by it. Voltages 3V~5.5V are the dc control's supply voltage and operating voltage, respectively. Workable in an dc switcher where -40°C~125°C TJ is the -40°C~125°C TJrm. As it has a Surface Mount value, it can be used for general dc dc regulator. The dcdc regulator features Enable, Frequency Control, Ramp for efficient switching control. The switch converters are connected to a SWITCHING CONTROLLER analog IC. There are a terminal (s) on the switching converters that are designed at DUAL. The 20 terminations can be used for a wide range of dc switching. These dc dc converter ics adapt a variety of control techniques, including PULSE WIDTH MODULATION. There is a DC switcher's nominal voltage of 5V. Other relevant dc to dc converter ics can be found by searching "MCP1631". The switching converter has a total of 20 pins. Specifically, switching converter falls under the Switching Regulator or Controllers category. It's important to remember that the dc dc regulator's normaloutput current is 250mA, so you should note it down when starting a new project. As a result of this, the maximum duty cycle of the voltage regulator dc to dc must remain 10 % during power-up and power-down. DC switcher's Surface Mount qualifies it for most applications and prototypes. Switching controller operates at 1MHz Hz. 5.5V is the nominal working voltage. At 2MHz, this controller will mostly work as expected.
MCP1631V-E/ST Features
Transistor Driver Outputs
Enable, Frequency Control, Ramp
PULSE WIDTH MODULATION
Max Duty Cycle: 10 %
Frequency: 1MHz
Switching Frequency: 2MHz
MCP1631V-E/ST Applications
There are a lot of Microchip Technology MCP1631V-E/ST DC to DC converter applications.
- Solar power plants
- Computer rooms
- Product burn-in
- Wind power
- Handheld GPS
- Direct power supply system
- Printing equipment
- Sensitive electronic devices
- Refrigerators of central air conditioners
- Imported equipment
