MCP1631VT-E/ML
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-VFQFN Exposed Pad |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP1631 |
| Function | Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 5V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 250mA |
| Voltage - Supply (Vcc/Vdd) | 3V~5.5V |
| Control Features | Enable, Frequency Control, Ramp |
| Input Voltage (Min) | 3V |
| Topology | Sepic |
| Control Mode | VOLTAGE-MODE |
| Input Voltage (Max) | 5.5V |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 2.5ns |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 2.7 ns |
| Switcher Configuration | SINGLE |
| Max Frequency | 2MHz |
| Switching Frequency | 2MHz |
| Duty Cycle | 10 % |
| Length | 4mm |
| Width | 4mm |
| RoHS Status | ROHS3 Compliant |
MCP1631VT-E/ML Overview
In the 20-VFQFN Exposed Pad package, the switching controller meets most application requirements. dc motor controller is suitable for 1 output generation. There is a Tape & Reel (TR) solid enclosure around the pmic. The system can process Transistor Driver dc switching's outputs (s). A 3V~5.5V voltage is supplied to the dc control and used for operating it. Suitable for working in an dc switcher that has a -40°C~125°C TJ. dc dc regulators can be carried out with Surface Mount. Featured in the dcdc regulator is Enable, Frequency Control, Ramp which allows efficient switching control. An analog IC with the SWITCHING CONTROLLER signal is connected to the switch converters. There are a QUAD terminal on the switching converters. 20 terminations with a variety of function. These dc dc converter ics adapt several control methods, including PULSE WIDTH MODULATION. DC switcher's voltage input of 5V. You can find other relevant dc to dc converter ics by searching "MCP1631". Pins number 20 of switching converter in total. Particularly, switching converter is a type of Switching Regulator or Controllers. It is recommended that the dc dc voltage regulator's minimum input voltage be 3V. The dc to dc regulator can only accept a maximum input voltage of 5.5V. normally, the dc dc regulator's output current is 250mA, which you should keep in mind when starting a project. In most applications and prototypes, DC switcher's Surface Mount makes it suitable. DC regulators have a maximum frequency of 2MHz. 2MHz is the frequency at which this controller can mostly perform fine.
MCP1631VT-E/ML Features
Transistor Driver Outputs
Enable, Frequency Control, Ramp
PULSE WIDTH MODULATION
Switching Frequency: 2MHz
MCP1631VT-E/ML Applications
There are a lot of Microchip Technology MCP1631VT-E/ML DC to DC converter applications.
- ATMs
- Special machining machine tools
- Series voltage regulation circuits
- Experimental setup
- Hydro power
- Computed tomography (CT)
- Wide-range voltage regulation circuits
- Motor controller circuits
- Industrial robots
- Medical monitoring systems
