MCP1650S-E/MS

8 Terminals 2.7V~5.5V 8-Pin MCP1650 DC to DC converter ICSWITCHING CONTROLLER 1 Outputs 750kHz Transistor Driver

Manufacturer: Microchip Technology
Nocochips NO: 536-MCP1650S-E/MS
Package: 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
Datasheet: PDF
Stock: 777
Description: 8 Terminals 2.7V~5.5V 8-Pin MCP1650 DC to DC converter ICSWITCHING CONTROLLER 1 Outputs 750kHz Transistor Driver (Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
Number of Pins	8
Operating Temperature	-40°C~125°C TJ
Packaging	Tube
Published	2004
JESD-609 Code	e3
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
Terminal Finish	Matte Tin (Sn)
Subcategory	Switching Regulator or Controllers
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	MCP1650
Function	Step-Up, Step-Up/Step-Down
Number of Outputs	1
Output Voltage	100V
Output Type	Transistor Driver
Max Output Current	100mA
Input Voltage-Nom	3.3V
Analog IC - Other Type	SWITCHING CONTROLLER
Operating Supply Current	120μA
Output Configuration	Positive
Output Current	100mA
Voltage - Supply (Vcc/Vdd)	2.7V~5.5V
Control Features	Current Limit, Enable, Low Battery, Power Good
Max Output Voltage	100V
Topology	Boost, Flyback, SEPIC
Min Input Voltage	2V
Control Mode	CURRENT-MODE
Frequency - Switching	750kHz
Max Input Voltage	5.5V
Control Technique	PULSE WIDTH MODULATION
Synchronous Rectifier	No
Min Output Voltage	3.3V
Switcher Configuration	SINGLE
Max Frequency	850kHz
Max Duty Cycle	88 %
Duty Cycle (Max)	80%
Height	850μm
Length	3mm
Width	3mm
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

MCP1650S-E/MS Overview

It comes in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) package, so switching controller can be used for most applications. For 1 outputs, the dc motor controller is appropriate. An enclosure of Tube is used to package the PMIC. There are Transistor Driver dc switching's output (s) that it can handle. A 2.7V~5.5V voltage is supplied to the dc control and used for operating it. Worked in a -40°C~125°C TJ dc switcher before. The switching controller is capable of switching at the 750kHz position. As it has a Surface Mount value, it can be used for general dc dc regulator. To provide efficient switching control, Current Limit, Enable, Low Battery, Power Good is included in the dcdc regulator. Thare switch converters are connected to an analog integrated circuit (IC) of type SWITCHING CONTROLLER. DUAL are the position of the terminal of the switching converters. 8 terminations with a variety of function. This dc dc converter ic uses a variety of control techniques, including PULSE WIDTH MODULATION. 3.3V nominal DC switcher's voltage input. You can find other relevant dc to dc converter ics by searching "MCP1650". Switching converter has a total of 8 pins. Specially, switching converter corresponds to type Switching Regulator or Controllers. Statistically, DC regulator outputs 100V volts. If you are starting a new project, you should note the dc dc regulator's typical output current is 100mA. Voltage regulator dc to dc is designed to operate at 88 % duty cycle during power-ups and power-downs to ensure reliability. The Surface Mount makes DC switcher suitable for most applications and prototypes. There is a maximum frequency of 850kHz for this dc regulators. The maximum input voltage of the dc switcher is 5.5V, so users need to limit the voltage accordingly. Voltage 2V is needed for the supply. In this case, the dc switcher won't produce more than 100mA watts of output current. Datasheets indicate that the switching converter can output 100V volts at its maximum. There is a 120μA volt supply current. voltage controllers with a minimum voltage output of 3.3V cannot operate.