MCP1653R-E/UN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Termination | SMD/SMT |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.5mm |
| Frequency | 750kHz |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP1653 |
| Function | Step-Up, Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 12V |
| Output Type | Transistor Driver |
| Max Output Current | 100mA |
| Input Voltage-Nom | 3.3V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Operating Supply Current | 120μA |
| Output Configuration | Positive |
| Output Current | 100mA |
| Voltage - Supply (Vcc/Vdd) | 2.7V~5.5V |
| Control Features | Current Limit, Enable, Low Battery, Power Good |
| Max Output Voltage | 100V |
| Topology | Boost, Flyback, SEPIC |
| Min Input Voltage | 2V |
| Control Mode | CURRENT-MODE |
| Max Input Voltage | 5.5V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Min Output Voltage | 3.3V |
| Switcher Configuration | SINGLE |
| Duty Cycle (Max) | 80% |
| Height | 950μm |
| Length | 3mm |
| Width | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP1653R-E/UN Overview
Capsuled in the 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) package, the switching controller can be used for a wide range of applications. There is sufficient capacity to generate switching controller for outputs 1. PMIC is packaged in a solid enclosure of Tube. There are Transistor Driver dc switching's output (s) that it can handle. dc control's supply and operating voltages are 2.7V~5.5V. Qualified to work in a -40°C~125°C TJ dc switcher. dc dc regulators can be carried out with Surface Mount. For efficient switching control, the dcdc regulator features Current Limit, Enable, Low Battery, Power Good. An analog IC with the SWITCHING CONTROLLER signal is connected to the switch converters. There are a terminal (s) on the switching converters that are designed at DUAL. There are many different types of terminations for 10. It includes PULSE WIDTH MODULATION as one of the control techniques dc dc converter ic adapts. DC switcher's input voltageis set to 3.3V. Searching "MCP1653" will return other relevant dc to dc converter ics. There are a total of 10 pins on switching converter. Switching converter is a special type of Switching Regulator or Controllers. Test statistics indicate DC regulator outputs 12V voltage. You should note that the dc dc regulator's usual output current is 100mA. Having a Surface Mount makes DC switcher ideal for most prototype and application designs. Switching controller operates at a frequency of 750kHz. The maximum input voltage of dc switcher is 5.5V, so users should limit their voltage accordingly. 2V is the required supply voltage. DC switchers cannot produce output currents greater than 100mA. The datasheet indicates that the switching converter can output 100V volts at its maximum. There is 120μA supply current for it. A voltage controller's lowest output voltage cannot be less than 3.3V.
MCP1653R-E/UN Features
Transistor Driver Outputs
Current Limit, Enable, Low Battery, Power Good
PULSE WIDTH MODULATION
Frequency: 750kHz
MCP1653R-E/UN Applications
There are a lot of Microchip Technology MCP1653R-E/UN DC to DC converter applications.
- Balance equipment
- Printing
- Network technology
- seismic instrument power circuits
- Current source circuits
- Geothermal power
- Mobile phones
- Constant current circuits
- Packaging
- Refrigerators of central air conditioners
