MCP1653S-E/UN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP1653 |
| Function | Step-Up, Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 100V |
| Output Type | Transistor Driver |
| Max Output Current | 100mA |
| Input Voltage-Nom | 3.3V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 560mA |
| Voltage - Supply (Vcc/Vdd) | 2.7V~5.5V |
| Control Features | Current Limit, Enable, Low Battery, Power Good |
| Max Output Voltage | 100V |
| Topology | Boost, Flyback, SEPIC |
| Min Input Voltage | 2V |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 750kHz |
| Max Input Voltage | 5.5V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Min Output Voltage | 3.3V |
| Switcher Configuration | SINGLE |
| Max Frequency | 850kHz |
| Duty Cycle (Max) | 80% |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP1653S-E/UN Overview
The switching controller fits in the 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) package and is ideal for most applications. There is sufficient capacity to generate switching controller for outputs 1. PMIC packaging is solid with a Tube enclosure. There are Transistor Driver dc switching's output (s) that it can handle. This dc control has a supply voltage and operating voltage of 2.7V~5.5V. Worked in an dc switcher with a -40°C~125°C TJ rating. It can switch at 750kHz. dc dc regulators can be carried out with Surface Mount. The dcdc regulator features Current Limit, Enable, Low Battery, Power Good for efficient switching control. Connected to a SWITCHING CONTROLLER analog IC, the switch converters are connected to a power supply. There are a DUAL terminal on the switching converters. 10 terminations with a variety of function. This dc dc converter ic uses a variety of control techniques, including PULSE WIDTH MODULATION. A DC switcher's nominal voltage of 3.3V is input. A search for "MCP1653" will reveal other relevant dc to dc converter ics. In total, switching converter has 10 pins. Specifically, switching converter falls under the Switching Regulator or Controllers category. A 100V voltage of DC regulator was detected in the test statistics. You should note that the dc dc regulator's usual output current is 560mA. DC switcher's Surface Mount makes it qualified for most application and prototype designs. DC switcher'sIt is estimated that this dc regulatorhas a maximum frequency of 850kHz. In order to limit the voltage of a dc switcher whose maximum input voltage is 5.5V, it must be limited by the user. Voltage 2V is necessary for the supply. There will be 100mA output current greater than 100mA from the dc switcher. Its datasheet indicates the switching converter can output a maximum of 100V volts. 3.3V voltage output is lower than 3.3V.
MCP1653S-E/UN Features
Transistor Driver Outputs
Switching Frequency: 750kHz
Current Limit, Enable, Low Battery, Power Good
PULSE WIDTH MODULATION
MCP1653S-E/UN Applications
There are a lot of Microchip Technology MCP1653S-E/UN DC to DC converter applications.
- Digital precision reference circuits
- Elevator lighting
- Telecommunications equipment
- Packaging
- Hydraulic presses
- Computer rooms
- Motor controller circuits
- Household control circuits
- Die casting equipment
- Injection molding machinery
