MCP19214T-E/MQ
| Parameters | |
|---|---|
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 28 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Base Part Number | MCP19214 |
| Function | Step-Up/Step-Down |
| Number of Outputs | 2 |
| Output Type | PWM Signal |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | DUAL SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Voltage - Supply (Vcc/Vdd) | 4.5V~42V |
| Control Features | Dead Time Control, Frequency Control, Ramp, Soft Start |
| Input Voltage (Min) | 4.5V |
| Topology | Boost, Cuk, Flyback, SEPIC |
| Control Mode | CURRENT-MODE |
| Output Current-Max | 0.035A |
| Frequency - Switching | 31.25kHz~2MHz |
| Control Technique | PULSE WIDTH MODULATION |
| Supply Current-Max (Isup) | 10mA |
| Synchronous Rectifier | Yes |
| Screening Level | AEC-Q100; TS-16949 |
| Serial Interfaces | I2C |
| Height Seated (Max) | 1mm |
| Length | 5mm |
| Width | 5mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 28-VFQFN Exposed Pad |
| Surface Mount | YES |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| Series | Automotive, AEC-Q100 |
MCP19214T-E/MQ Overview
In the 28-VFQFN Exposed Pad package, the switching controller meets most application requirements. 2 outputs can be generated with the dc motor controller. Packaged in solid enclosures, this pmic has a Tape & Reel (TR) rating. A total of PWM Signal dc switching's outputs can be handled by it. DC control operates at 4.5V~42V volts and has 4.5V~42V supply voltage. Worked in an dc switcher with a -40°C~125°C TJ rating. This switching controller can switch at 31.25kHz~2MHz. A generalization of dc dc regulator can be made using Surface Mount. The dcdc regulator features Dead Time Control, Frequency Control, Ramp, Soft Start for efficient switching control. A DUAL SWITCHING CONTROLLER analog IC is connected to the switch converters. Terminal (s) of the switching converters are designed at the QUAD position. A variety of dc switching's functions can be performed on 28 terminations. These dc dc converter ics adapt a variety of control techniques, including PULSE WIDTH MODULATION. The nominal DC switcher's voltage input is 12V. MCP19214 can be searched for other relevant dc to dc converter ics. Input voltage of dc dc voltage regulator should be 4.5V. Current is output to the greatest value of 0.035A. Automotive, AEC-Q100 series dc to dc voltage regulator belong to this series. There must be a voltage supply of 5V volts. The controller should not be supplied with more current than 10mA.
MCP19214T-E/MQ Features
PWM Signal Outputs
Switching Frequency: 31.25kHz~2MHz
Dead Time Control, Frequency Control, Ramp, Soft Start
PULSE WIDTH MODULATION
MCP19214T-E/MQ Applications
There are a lot of Microchip Technology MCP19214T-E/MQ DC to DC converter applications.
- Serial communication converter
- Fire elevators
- Network technology
- Scientific research
- Magnetohydrodynamic power
- Sink circuits
- Large fire protection systems
- Wind power
- Elevator lighting
- Die casting equipment
