MCP6001T-E/LT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6001 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 1 |
| Nominal Supply Current | 100μA |
| Output Current | 23mA |
| Current - Supply | 100μA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Input Offset Voltage (Vos) | 4.5mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 112dB |
| Power Supply Rejection Ratio (PSRR) | 86dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 1mm |
| Length | 2.25mm |
| Width | 1.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6001T-E/LT Overview
Op amp is packaged in 5-TSSOP, SC-70-5, SOT-353 case. This is a General Purpose type op amp. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. The number of terminations approaches 5. In total, there are 5 pins on this op amp ic. I would like to remind you that this buffer op amp should be powered by an 5V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. A total of 5 pins are present on the instrumentation amplifier. Op amp ic rates 4.5mV for input offset voltage. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . 112dB should remain the voltage gain. There are 1 channels on the operational amplifiers. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage. As a result of this, the buffer amplifier is packed in TAPE AND REEL. This electronic part is recommended to be used with an 100μA supply for best performance.
MCP6001T-E/LT Features
5 Pins
supply voltage of 5V
112dB voltage gain
Output Type: Rail-to-Rail
MCP6001T-E/LT Applications
There are a lot of Microchip Technology MCP6001T-E/LT Instrumentational OP Amps applications.
- Precision measurement
- Radiation thermometry transducers
- Gaming industry
- Inverse/same-phase proportional circuit
- Fast A/D and D/A converters
- E-book readers
- Power generator
- Medical imaging
- High/low-pass filter circuit
- High gain DC amplifier
