MCP6001T-I/OT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6001 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 1 |
| Voltage | 6V |
| Operating Supply Current | 100μA |
| Nominal Supply Current | 100μA |
| Output Current | 23mA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Output Current per Channel | 23mA |
| Input Offset Voltage (Vos) | 4.5mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 112dB |
| Power Supply Rejection Ratio (PSRR) | 86dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 1.3mm |
| Length | 3.1mm |
| Width | 1.8mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6001T-I/OT Overview
In the package, you will find a SC-74A, SOT-753-case to contain the op amp ic. An op amp of this type is a General Purpose-type. Linear amplifier is delivered in a Tape & Reel (TR) case. The number of terminations approaches 5. A total of 5 pins are attached to buffer op amp. Please take in mind that op amp should be run at 5V. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. The op amp ic has an array of 5 pins on it. There is an input offset voltage of 4.5mV for this buffer op amp. Surface Mount is the recommended mounting type of operational amplifiers. With regard to operating temperature, this op amp functions well at -40°C~85°C. Using an 100μA supply current, this operational amplifier ics can be operated. It is recommended to keep the voltage gain at 112dB at all times. Op amp ic has 1 channels. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. The operating supply voltage of the buffer op amp is rated at 5.5V. TAPE AND REEL is adopted to pack the instrumentation amplifier.
MCP6001T-I/OT Features
5 Pins
supply voltage of 5V
112dB voltage gain
Output Type: Rail-to-Rail
MCP6001T-I/OT Applications
There are a lot of Microchip Technology MCP6001T-I/OT Instrumentational OP Amps applications.
- Communication
- Weak signal detection
- Fast A/D and D/A converters
- Image computer boards
- Radar
- Semiconductor detectors
- Power generator
- Power transmission
- Exponential operation circuits
- Measurements of Wheatstone bridge
