MCP6002-E/MS
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6002 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 2 |
| Nominal Supply Current | 100μA |
| Output Current | 23mA |
| Current - Supply | 100μA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Input Offset Voltage (Vos) | 4.5mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 112dB |
| Power Supply Rejection Ratio (PSRR) | 86dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | NO |
| Micropower | YES |
| Programmable Power | NO |
| Height | 950μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6002-E/MS Overview
It is packaged in an 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case that protects the operational amplifiers from damage. Op amps are General Purpose types of amplifier on the chip. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. During the past two weeks, there have been close to 8 terminations. The total number of pins on linear amplifier is 8. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. Instrumentation amplifier is a part of Operational Amplifier. It has 8 pins that make up the linear amplifier. In terms of input offset voltage, operational amplifier rates 4.5mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . You should keep the voltage gain at 112dB for the time being. Instrumentation amplifier has 2 channels on it. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage. There is a recommendation that this electrical part be used with a supply with 100μA current rating.
MCP6002-E/MS Features
8 Pins
supply voltage of 5V
112dB voltage gain
Output Type: Rail-to-Rail
MCP6002-E/MS Applications
There are a lot of Microchip Technology MCP6002-E/MS Instrumentational OP Amps applications.
- Weighing systems
- Portable media players
- Division circuits
- Power control
- Micro signal measurement
- Switching amplifier
- Instrumentation
- High gain DC amplifier
- Active probe
- Commercial audio systems
