MCP6002-E/P
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | MCP6002 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 2 |
| Operating Supply Current | 100μA |
| Nominal Supply Current | 100μA |
| Output Current | 23mA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Output Current per Channel | 23mA |
| Input Offset Voltage (Vos) | 4.5mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 112dB |
| Power Supply Rejection Ratio (PSRR) | 86dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | NO |
| Micropower | YES |
| Programmable Power | NO |
| Height | 3.3mm |
| Length | 9.27mm |
| Width | 6.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6002-E/P Overview
Op amp is packaged in 8-DIP (0.300, 7.62mm) case. This is a General Purpose type op amp. The op amp is delivered to you in a Tube case. The number of terminations is approaching the 8 mark. A total of 8 pins are located on this board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. It has 8 pins that make up the linear amplifier. As far as the input offset voltage is concerned, linear amplifier rates at 4.5mV. This electronic part is recommended for mounting type Through Hole. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~125°C . It is possible to operate this buffer amplifier from a supply current of 100μA . 112dB should remain the voltage gain. There are 2 channels on the operational amplifiers. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage.
MCP6002-E/P Features
8 Pins
supply voltage of 5V
112dB voltage gain
Output Type: Rail-to-Rail
MCP6002-E/P Applications
There are a lot of Microchip Technology MCP6002-E/P Instrumentational OP Amps applications.
- Automotive sensors
- Laptop
- Large motor controllers
- Television broadcasting equipment
- Automatic control
- Proportional counter tubes
- Tablets
- Communication
- Instrumentation
- Navigation
