MCP6002-E/SN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6002 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 2 |
| Nominal Supply Current | 100μA |
| Output Current | 23mA |
| Current - Supply | 100μA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Input Offset Voltage (Vos) | 4.5mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 112dB |
| Power Supply Rejection Ratio (PSRR) | 86dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | NO |
| Micropower | YES |
| Programmable Power | NO |
| Height | 1.25mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6002-E/SN Overview
There is a 8-SOIC (0.154, 3.90mm Width) case package that contains the instrumentation amplifiers. An op amp of this type is a General Purpose-type. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. The number of terminations approaches 8. Buffer amplifier has a total of 8 pins on it. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 8 pins are available on the instrumentation amplifier. There is an input offset voltage of 4.5mV for this buffer op amp. This electronic part is recommended for mounting type Surface Mount. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~125°C . You should keep the voltage gain at 112dB for the time being. Buffer op amp is equipped with 2 channels on the device. On the output type, there are Rail-to-Rail different types of op amps. The operating supply voltage of the buffer op amp is rated at 5.5V. As a result, it is recommended that a power supply of 100μA be used with this electronic part.
MCP6002-E/SN Features
8 Pins
supply voltage of 5V
112dB voltage gain
Output Type: Rail-to-Rail
MCP6002-E/SN Applications
There are a lot of Microchip Technology MCP6002-E/SN Instrumentational OP Amps applications.
- Signal filtering
- Non-polarized electrodes
- single/dual op amp sum and difference circuits
- High speed sample
- Television
- Power generator
- Oscilloscopes
- Integrator circuits
- Communication
- Multiplication circuits
