MCP6002T-I/MS
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6002 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Nominal Supply Current | 100μA |
| Output Current | 23mA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Input Offset Voltage (Vos) | 4.5mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 112dB |
| Power Supply Rejection Ratio (PSRR) | 86dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 1kHz |
| Programmable Power | NO |
| Height | 939.8μm |
| Length | 2.9972mm |
| Width | 2.9972mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6002T-I/MS Overview
Packaged in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case, the buffer op amp is ready to use. General Purpose-type instrumentation amplifiers are used in this application. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are located on this board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. Instrumentation amplifier is a part of Operational Amplifier. In total, the buffer amplifier consists of 8 pins. There is an input offset voltage of 4.5mV for this buffer op amp. For this electrical component, Surface Mount is the recommended mounting type. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . Keeping the voltage gain at 112dB is the best course of action. This op amp ic has 2 circuits. The op amp ic has 2 channels on it. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. The operating supply voltage of the buffer op amp is rated at 5.5V. As a result of this, the buffer amplifier is packed in TAPE AND REEL.
MCP6002T-I/MS Features
8 Pins
supply voltage of 5V
112dB voltage gain
Output Type: Rail-to-Rail
MCP6002T-I/MS Applications
There are a lot of Microchip Technology MCP6002T-I/MS Instrumentational OP Amps applications.
- Active probe
- Biopotential
- Proportional operation circuits
- Industrial control system
- Industrial applications including automation
- Multiplication circuits
- Instrumentation
- Computer workstations
- Test equipment
- single/dual op amp sum and difference circuits
