MCP6004-E/P
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Base Part Number | MCP6004 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 2/5V |
| Number of Channels | 4 |
| Operating Supply Current | 100μA |
| Nominal Supply Current | 100μA |
| Output Current | 23mA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Output Current per Channel | 23mA |
| Input Offset Voltage (Vos) | 4.5mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 112dB |
| Power Supply Rejection Ratio (PSRR) | 86dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Height | 4.953mm |
| Length | 19.69mm |
| Width | 7.112mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6004-E/P Overview
A 14-DIP (0.300, 7.62mm) case is used to package the op amp. An op amp ic of the General Purpose type. A Tube case is used for delivering the op amp. The number of terminations approaches 14. A total of 14 pins are located on this board. Please take in mind that this instrumentation amplifier should be run at 5V. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. Linear amplifier includes 14 pins. Op amp ic rates 4.5mV for input offset voltage. It is recommended that this electronic component be mounted using the Through Hole mounting type. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . In order for this instrumentation amplifier to operate, the supply current needs to be between 100μA and 10 . You should keep the voltage gain at 112dB for the time being. There are a total of 4 channels available on the op amps. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. The operating supply voltage of the buffer op amp is rated at 5.5V.
MCP6004-E/P Features
14 Pins
supply voltage of 5V
112dB voltage gain
Output Type: Rail-to-Rail
MCP6004-E/P Applications
There are a lot of Microchip Technology MCP6004-E/P Instrumentational OP Amps applications.
- High input resistance broadband
- Industrial applications including automation
- Television
- Active probe
- Automotive sensors
- Commercial audio systems
- Signal amplification
- Video amplifiers
- RF cable systems
- Video computer boards
