MCP6004-E/SL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6004 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 2/5V |
| Number of Channels | 4 |
| Nominal Supply Current | 100μA |
| Output Current | 23mA |
| Current - Supply | 100μA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Input Offset Voltage (Vos) | 4.5mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 112dB |
| Power Supply Rejection Ratio (PSRR) | 86dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Height | 1.25mm |
| Length | 8.65mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6004-E/SL Overview
The linear amplifier is packaged in a 14-SOIC (0.154, 3.90mm Width) case. Op amps are General Purpose types of amplifier on the chip. There is a Tube case that is delivered with the instrumentation amplifiers. During the past two weeks, there have been close to 14 terminations. A total of 14 pins are located on this board. Please take in mind that op amp should be run at 5V. Instrumentation amplifier is a part of Operational Amplifier. In total, the buffer amplifier consists of 14 pins. As far as the input offset voltage is concerned, linear amplifier rates at 4.5mV. This electronic part is recommended for mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureYou should keep the voltage gain at 112dB for the time being. There are a total of 4 channels available on the op amps. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage. There is a recommendation that this electrical part be used with a supply with 100μA current rating.
MCP6004-E/SL Features
14 Pins
supply voltage of 5V
112dB voltage gain
Output Type: Rail-to-Rail
MCP6004-E/SL Applications
There are a lot of Microchip Technology MCP6004-E/SL Instrumentational OP Amps applications.
- Logarithmic operation circuits
- Proportional counter tubes
- RF cable systems
- Automatic control
- Signal operation
- Video computer boards
- Digital cameras
- Oscilloscopes
- Industrial control system
- Fission chambers
