MCP6004-I/SL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Frequency | 1MHz |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6004 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 2/5V |
| Number of Channels | 4 |
| Nominal Supply Current | 100μA |
| Output Current | 23mA |
| Current - Supply | 100μA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Input Offset Voltage (Vos) | 4.5mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 112dB |
| Power Supply Rejection Ratio (PSRR) | 86dB |
| Low-Offset | NO |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Height | 1.25mm |
| Length | 8.65mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6004-I/SL Overview
It is packaged in an 14-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. The instrumentation amplifier in this picture is of the General Purpose-type. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. A total of 14 terminations have been reported in the past few weeks. A total of 14 pins are attached to buffer op amp. Please take in mind that op amp should be run at 5V. This particular linear amplifier is a type of Operational Amplifier device, to be precise. It has 14 pins that make up the linear amplifier. Op amp ic rates 4.5mV for input offset voltage. The mounting type that is recommended for this electrical part is Surface Mount. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~85°C . Maintain 112dB as the voltage gain. There are 4 channels on the operational amplifiers. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. The operating supply voltage of the buffer op amp is rated at 5.5V. To run supply current of buffer amplifier under 100μA.
MCP6004-I/SL Features
14 Pins
supply voltage of 5V
112dB voltage gain
Output Type: Rail-to-Rail
MCP6004-I/SL Applications
There are a lot of Microchip Technology MCP6004-I/SL Instrumentational OP Amps applications.
- Gaming industry
- Integrator circuits
- High speed sample
- Blood pressure sensors
- single/dual op amp sum and difference circuits
- Portable docking station
- Micro signal measurement
- pH (acidity)
- Fission chambers
- Television broadcasting equipment
