MCP6004T-E/ST
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6004 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Elements | 4 |
| Power Supplies | 2/5V |
| Operating Supply Current | 100μA |
| Nominal Supply Current | 100μA |
| Output Current | 23mA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Output Current per Channel | 23mA |
| Input Offset Voltage (Vos) | 4.5mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 112dB |
| Power Supply Rejection Ratio (PSRR) | 86dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6004T-E/ST Overview
There is a 14-TSSOP (0.173, 4.40mm Width) case package that contains the instrumentation amplifiers. There are two types of operational amplifiers in this circuit. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. The number of terminations approaches 14. The pins on this board total to 14 in total. I would like to remind you that this buffer op amp should be powered by an 5V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 14 pins are located on the operational amplifiers. With regard to input offset voltage, instrumentation amplifier is rated at 4.5mV. Surface Mount is the recommended mounting type of operational amplifiers. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . An 100μA volt supply current is needed for this linear amplifier to operate. Keeping the voltage gain at 112dB is the best course of action. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. This linear amplifier has a total of 4 elements. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage. It is used TAPE AND REEL to pack the op amps.
MCP6004T-E/ST Features
14 Pins
supply voltage of 5V
112dB voltage gain
Output Type: Rail-to-Rail
MCP6004T-E/ST Applications
There are a lot of Microchip Technology MCP6004T-E/ST Instrumentational OP Amps applications.
- Video computer boards
- Weighing systems
- Proportional counter tubes
- Navigation
- Medical imaging
- High gain DC amplifier
- Laptop
- Non-polarized electrodes
- Signal amplification
- Ultrasound transducers
