MCP6004T-I/SL
| Parameters | |
|---|---|
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6004 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 2/5V |
| Number of Channels | 4 |
| Operating Supply Current | 100μA |
| Nominal Supply Current | 100μA |
| Output Current | 23mA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Output Current per Channel | 23mA |
| Input Offset Voltage (Vos) | 4.5mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 112dB |
| Power Supply Rejection Ratio (PSRR) | 86dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 1kHz |
| Height | 1.5mm |
| Length | 8.65mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
MCP6004T-I/SL Overview
In order to protect the op amps, a 14-SOIC (0.154, 3.90mm Width) case is used. The instrumentation amplifier in this picture is of the General Purpose-type. Linear amplifier is delivered in a Tape & Reel (TR) case. A total of 14 terminations have been reported in the past few weeks. The total number of pins on linear amplifier is 14. I would like to remind you that this buffer op amp should be powered by an 5V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. There are 14 pins on this chip. In terms of input offset voltage, operational amplifier rates 4.5mV. This electrical part should be mounted using type Surface Mount. With regard to operating temperature, op amp ranges -40°C~85°C. Using a supply current of 100μA , this buffer op amp will be able to operate. Op amp is a member of the 112dB's 112dB family. Op amp ic has 4 channels. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage. An buffer amplifier is packed in a TAPE AND REEL-shape according to the design.
MCP6004T-I/SL Features
14 Pins
supply voltage of 5V
112dB voltage gain
Output Type: Rail-to-Rail
MCP6004T-I/SL Applications
There are a lot of Microchip Technology MCP6004T-I/SL Instrumentational OP Amps applications.
- High speed sample
- Navigation
- Band-pass filter
- Video conversion and routing
- Tablets
- Non-polarized electrodes
- RF cable systems
- Automation control systems
- Television
- Vehicle electronics
