MCP601-E/P
| Parameters | |
|---|---|
| Operating Supply Current | 230μA |
| Nominal Supply Current | 230μA |
| Output Current | 22mA |
| Slew Rate | 2.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V |
| Output Current per Channel | 22mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 2.8MHz |
| Unity Gain BW-Nom | 2800 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 700μV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 4.953mm |
| Length | 10.16mm |
| Width | 7.112mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MCP601 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
MCP601-E/P Overview
In order to protect the op amps, a 8-DIP (0.300, 7.62mm) case is used. An op amp ic of the General Purpose type. A Tube case is used to deliver the buffer op amp. The number of terminations approaches 8. The pins on this board total to 8 in total. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. It should be noted that this op amp is a type of Operational Amplifier device. It has 8 pins that make up the linear amplifier. In terms of input offset voltage, operational amplifier rates 2mV. For this electronic part, it is recommended that you mount it with type Through Hole. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. An 230μA volt supply current is needed for this linear amplifier to operate. There should be no change in the voltage gain. Instrumentation amplifier has 1 channels on it. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. The operating supply voltage of the buffer op amp is rated at 5.5V.
MCP601-E/P Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP601-E/P Applications
There are a lot of Microchip Technology MCP601-E/P Instrumentational OP Amps applications.
- Computer workstations
- High gain DC amplifier
- Digital cameras
- Multimedia playback equipment
- Active probe
- Inverse/same-phase proportional circuit
- Automatic control
- Oscilloscopes
- Comparator
- Fission chambers
