MCP601T-I/OT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C |
| Packaging | Cut Tape (CT) |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP601 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Max Output Current | 30mA |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 1 |
| Voltage | 5V |
| Number of Circuits | 1 |
| Nominal Supply Current | 230μA |
| Output Current | 22mA |
| Max Supply Current | 2mA |
| Slew Rate | 2.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 2.8MHz |
| Unity Gain BW-Nom | 2800 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 700μV |
| Settling Time | 4.5 μs |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 1.3mm |
| Length | 3.1mm |
| Width | 1.8mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP601T-I/OT Overview
Packaging for the buffer amplifier is in the form of a SC-74A, SOT-753 case. The instrumentation amplifier in this picture is of the General Purpose-type. As far as the packaging is concerned, buffer op amp is delivered in a Cut Tape (CT) case. The number of terminations approaches 5. Buffer amplifier has a total of 5 pins. It is important to remember that this op amp should be operated at a voltage of 5V volts. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. 5 pins are available on the instrumentation amplifier. As far as the input offset voltage is concerned, linear amplifier rates at 2mV. Surface Mount is the recommended mounting type for this linear amplifier. With regard to operating temperature, this op amp functions well at -40°C~85°C. Op amp is a member of the 115dB's 115dB family. During the manufacturing process, this buffer amplifier is divided into 1 circuits. Instrumentation amplifier has 1 channels on it. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. The operating supply voltage of the buffer op amp is rated at 5.5V. For packing the buffer amplifier, the TAPE AND REEL-axis is adopted.
MCP601T-I/OT Features
5 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP601T-I/OT Applications
There are a lot of Microchip Technology MCP601T-I/OT Instrumentational OP Amps applications.
- Logarithmic operation circuits
- Home audio systems
- Addition operation circuits
- Scintillation detectors
- Automatic control
- Inverse/same-phase proportional circuit
- Commercial audio systems
- Communication
- Vehicle electronics
- High-frequency data acquisition systems
