MCP601T-I/ST
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP601 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Elements | 1 |
| Power Supplies | 3/5V |
| Number of Circuits | 1 |
| Nominal Supply Current | 230μA |
| Output Current | 22mA |
| Slew Rate | 2.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V |
| Input Offset Voltage (Vos) | 2mV |
| Gain Bandwidth Product | 2.8MHz |
| Unity Gain BW-Nom | 2800 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 700μV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Wideband | NO |
| Length | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP601T-I/ST Overview
Packaged in a 8-TSSOP (0.173, 4.40mm Width) case, the buffer op amp is ready to use. There are two types of operational amplifiers in this circuit. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. There is a growing number of terminations approaching the number of 8. Linear amplifier has a total of 8 pins. I would like to remind you that this buffer op amp should be powered by an 5V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. 8 pins are located on the operational amplifiers. Op amp ic rates 2mV for input offset voltage. It is recommended that this electronic component be mounted using the Surface Mount mounting type. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~85°C. Maintain 115dB as the voltage gain. A instrumentation amplifier like this has 1 circuits. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. There are 1 elements in total in this linear amplifier. The operating supply voltage of the buffer op amp is rated at 5.5V. The linear amplifier is packaged by using a TAPE AND REEL axis.
MCP601T-I/ST Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP601T-I/ST Applications
There are a lot of Microchip Technology MCP601T-I/ST Instrumentational OP Amps applications.
- Biopotential
- Power control
- High-frequency data acquisition systems
- Broadcasting
- Vehicle electronics
- Strain gauges
- Automotive sensors
- Video data acquisition
- Car stereo
- Signal amplification
