MCP602-I/P
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | MCP602 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Operating Supply Current | 230μA |
| Nominal Supply Current | 230μA |
| Output Current | 22mA |
| Slew Rate | 2.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V |
| Output Current per Channel | 22mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 2.8MHz |
| Unity Gain BW-Nom | 2800 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 700μV |
| Low-Bias | YES |
| Micropower | YES |
| Height | 4.953mm |
| Length | 10.16mm |
| Width | 7.112mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP602-I/P Overview
Op amp is packaged in 8-DIP (0.300, 7.62mm) case. Op amps are General Purpose types of amplifier on the chip. Instrumentation amplifier is delivered in a Tube case. There have been a total of 8 terminations over the past year. It consists of a total of 8 pins in total. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 8 pins are located on the operational amplifiers. In terms of the input offset voltage, instrumentation amplifier rates at 2mV. The mounting type that is recommended for this electrical part is Through Hole. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~85°C . In order for this instrumentation amplifier to operate, the supply current needs to be between 230μA and 10 . It is a member of the 115dB's 115dB family. As far as the device is concerned, buffer amplifier has 2 channels. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. The operating supply voltage of the buffer op amp is rated at 5.5V.
MCP602-I/P Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP602-I/P Applications
There are a lot of Microchip Technology MCP602-I/P Instrumentational OP Amps applications.
- Voltage regulation circuit
- Multiplication circuits
- Signal amplification
- Video data acquisition
- High/low-pass filter circuit
- earphone
- Home audio systems
- Power generator
- Industrial control system
- Broadcasting
